Question about Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

Open Question

Diswasher won't run.

I have a Maytag QuietSeries 400 and it's got a green light on beside a box with a 3 in it (where you choose your cycle) and I cannot change it to another (e.g. Normail Wash). When I try to press the start button I get an "L" in the display window. I have tried turning it off and leaving it for a half hour or so and then turn back on but the same issue persists. Any ideas?

Posted by Kandice Nagel on

Ad

5 Related Answers

Anonymous

SOURCE: filter light still on "Red"

try holding ice type and child lock together for 3 seconds that worked on mine

Posted on Jan 08, 2008

Ad
aborcass

Ron Coons

  • 2651 Answers

SOURCE: Maytag MDB7600 issues

reach inside your d/w and jiggle the mushroom shaped float switch located on floor of d/w. should move freely up and down if its stuck up(or something lodged under it your unit wont fill with water

Posted on Mar 20, 2008

Ad

Anonymous

  • 3 Answers

SOURCE: maytag neptune won;t rinse

Check latch mechanism for alignment. Often operation of machine loosens latch mechanism causing internal switch for "door open (or ajar)" preventing rinse or spin cycle. Opening and closing door presses latch mechanism closing internal switch allowing for continue processing to rinse or spin cycles.

Posted on Apr 13, 2008

Anonymous

  • 525 Answers

SOURCE: Maytag Dishwasher Model: MDBTT59AW

My research indicates that this is a control board malfunction, but with so many different descriptions of failure, I am left confused.
You may reference the link below to help isolate your problem.


http://www.repairclinic.com/0088_9_1.asp#Level1_9

Posted on Jun 05, 2008

myob247

Georgia B

  • 1342 Answers

SOURCE: Maytag dryer [electric] MED9600 lights up but won't start

Possible causes for your issue include:

Blown fuse
Timer or motor inoperative
Housing wiring not properly connected to dryer
Bad door switch
Faulty "Push to Start" switch

It would probably be best to have a professional pinpoint the exact defect.

Click Here for a very good source of information on Maytag dryers

Posted on Jul 17, 2008

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bosch diswasher,model Sms68m02AU trips circuit breaker


rcd units trip from the milliamps that are in a short
it trips the rcd to prevent electrocution and acts in nano seconds besides being a circuit breaker for excessive current
the trip can be from moisture allowing a current leakage to ground or some other simple operation
I suggest that you get in a qualified electrician / bosch service technician to find the reason for the problem rcd

Sep 15, 2016 | Bosch Dishwashers

1 Answer

How should I clean the Maytag Quiet Series 300 with vinegar?


just fill it with water no soap and drop in vinegar right in the water and let it run its cycle

Jan 27, 2015 | matag Maytag QuietSeries 300 Dishwasher...

1 Answer

Washer is noisy in spin cycle and won't spin water out


but clutch or loose worn belt, also check bad motor coupler

Aug 02, 2014 | Maytag Bravos MEDB400VQ 29" Electric Dryer...

1 Answer

My Maytag QuietSeries 400 dishwasher won't start. Sometimes 88 flashes on the display and that's all. What does that mean? Model # MDB7601AWB


Dishwasher will not start Is the door open or unlatched?
Make sure the door is completely closed and latched. On models with a dual-digit display, the control displays "- -" during a cycle if it believes the door is not latched. Check for obstructions (spoons, etc), interfering with the door operation. A lower dish rack that is installed backward will also cause incomplete door closure.

Check your household electrical box to see if a fuse has blown or if the circuit breaker has tripped. If the unit has a plug-in power cord, make sure it is plugged in.

Does your dishwasher have a rotary timer knob? (Some Models)
The cycle selection must match the position of the timer knob. Turn the timer knob to the beginning of the preferred cycle. The timer knob should click when you reach the start of the cycle.

Is the control lock option activated?
Press and hold the Heated Dry option (button with lock icon) for three to five seconds and the light should turn off. Instructions are also placed on the label on top of the inner door to unlock the controls.

Is the delay start option activated?
To cancel the delay and cycle, press Cancel/Drain.

Has the motor stopped for less than 10 minutes?
The motor may have stopped due to an overload. If this is the case, the motor will automatically reset itself within 5-10 minutes.

Is the Start/Resume indicator flashing?
Opening the door or interrupting the power can stop the cycle. Close the door and press Start/Resume. If the Start/Resume indicator flashes three times when you press Start/Resume, the dishwasher is waiting for you to open the door after the last cycle. Open and close the door, and then press Start/Resume.
On models where the controls are on top of the door be sure to close the door within 3 seconds of pressing the Start/Resume to start or resume the dishwasher cycle.

Is the water shutoff valve (if installed) turned on?
Make sure that the water shutoff valve is turned on.

Jun 19, 2011 | Maytag Dishwasher

4 Answers

Maytag Quiet Series dishwasher won't start


Sounds like you have a bad Control Board

http://www.partstore.com/Part/Maytag/Maytag/MDB6600AWW/Maytag/Maytag/99003160/New.aspx

But with the price it cost, you might be better off buying a new dishwasher, preferably a different brand, cause that washer has some bad reviews

Oct 12, 2009 | Dishwashers

2 Answers

The clean light is blinking diswasher won't start


Push these buttons in this order High temp wash > Heated dry>High temp wash >Heated dry all the lights will come on and this will reset the board and run it through a short test cycle but more than likely it will come up again,It's a failure in the heating cycle either the heater itself or the turbidity sensor which sits mounted up into the tub right behind the drain pump...hope this helps

Sep 13, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

QuietSeries 100 Maytag dishwasher


I read all the blogs on this dishwasher and decided to buy a new one and use this one as landfill...
Nothing but junk.

Jan 27, 2009 | Maytag 24 in. MDB5651A Built-in Dishwasher

2 Answers

Maytag quiet series model #:MDBH950AWB


The dishwasher lights are all blinking, it starts randomly, like one in every 50 times you press the buttons. I have unplugged it to reset several times. Nothing is working. I'm looking for a solution to blinking lights and it not starting. is there any other way to reset the controls????

Jan 13, 2008 | Maytag 24 in. MDBH950AWS Built-in...

3 Answers

All the lights are flashing on Maytag Quiet Series 300


Try pressing heated wash, heated dry, then heated wash, heated dry. It should reset it. Also try pressing and holding the cancel button for 5 seconds to see if that works if the other doesnt.

Sep 23, 2007 | Maytag 24 in. MDB5651A Built-in Dishwasher

Not finding what you are looking for?
Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4369 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Maytag Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...