Airconditioner doesn't switch on, it keeps on flashing green LEDs
Airconditioner doesn't switch on and stay on but it switches itself off
Immediatetly and flashes timer and operator green LEDs. This is the second time this happens, it was previously resolved by a reset done by the repair agent. How is this reset perfomed, cause power off doesn't work?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
hi sir good day
the green light indicator flashing which indicates error detected by processor. now here is my solution on how will you fix the problem. if you are going to do it with your make sure you have proper tools and at least a basic knowledge in repairing. now unplugged the unit then open the back cover to gain access the internal part of the tv. now disconnect the connector wire going to inverter board for back light then turn the tv, if the indicator stays green doesn't blink then all the voltage out put from the power supply is normal the 5v stand by,5v switch, 12v and 24v are present, you have bad inverter board or the back light itself. another way is if you disconnect the connector wire going to inverter ballast board then still light indicator flashing and no PS_ON voltage coming from the main board which switch the power supply to turn on i may say you have bad processor board. make sure no bulging capacitors at the power supply replaced it with the same value a panasonic brand FM or FC series much better with low ESR 105c rating. you can find replacement parts at www.digikey.com . hope this will help you feel free to ask further question good luck.
Hello, I try to help. But your questions not spesific. Below are conditions lamp indicators that appear blinking and solutions (for samsung) :
1. If Timer and Lamp blinking --> Auto timer on/off was been set, picture will appear ~ 25 second. 2. If Timer and Standby/Temp blinking --> A cooling fan inside the set is not operating properly. 3. If Lamp and Standby/Temp blinking --> The lamp cover on the rear of the set is not installed properly.
If all the LEDs then try to turn off the power switch, wait a few seconds, and then turn it back on. If all the LEDs are still blinking, press Go and Job Cancel buttons together and let me know what LEDs stay on.
You may have to reset your printer, for when the green an red are flashing. Please do the following in order to reset the printer; 1-switch off printer itself 2-switch off at socket for 20 seconds 3-hold down both black buttons on front switch on at mains 4-switch on printer itself green and red flash together 5-now switch off at mains and leave for 3 seconds 6-while holding down both front buttons again, switch on at mains both green and red flash together so release 7-quickly hold down the left botton, the one with the scroll icon above it.
Hold this until it resets itself, - the print head will re charge and it will be obvious.
Restting by unpluggin rather than turning off at mains tends not to work.
If printer is blinking all the LEDs then try to turn off the power switch, wait a few seconds, and then turn it back on and try to print again. If all the LEDs are still blinking, press Go and Job Cancel buttons together and let me know what LEDs stay on.
To Calibrate , start and warm engine to normal operating temp. with engine idling turn blower switch to high, turn mode switch to panel, open all outlets, move temp lever to full cold.
press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (untill all leds illuminate.) all leds should light up for 5 seconds, rear wiper and intermittent rear wiper button leds will flash alternatly during calibration... after 60 seconds if only rear wiper button led is flashing, cal. is complete
This is the indicator configuration for the 2600, if the lights are yellow there is a problem.
The following indicator LEDs provide power, activity, and status information:
• POWER (green)—Lit when power is on
• RPS (green)
– Off—No redundant power supply (RPS) is present
– Blinking—System is booted, RPS is present, RPS failure
– Continuous on—System is booted, RPS is present, no RPS failure
• ACTIVITY (green)
– Slow, steady blinking—System is booting
– Blinks during system activity, such as interrupts and packet transfers
I suggest going to Cisco.com for full documentation on this product.