Question about Samsung HLR5667W 56" Rear Projection HDTV
SOURCE: samsung green lines....
From past experience only two things can cause this. First is the cable going from the digital board to the DMD board. Make sure you disconnect the power, and use caution disconnecting the plug or tightening it, not to strip the plastic tension screws. Don't use power screwdriver for loosening or tightening this DVI type cable. Second is the digital board itself that can cause green interference lines in picture. For this, you may consider sending the module, which is the large shielded box where the cable screws on to back of set, out for service or rebuild. Reason being it is cheaper than buying replacement digital board. If it is the board itself, start by running a search on it by part number to see who has one. As I recall, the part number should be BP94-02084A, on your model. Good luck, Russmann.
Posted on Nov 28, 2008
SOURCE: colored lines and rectangles
Sounds like a problem on the digital board. try hard booting (unplug for 2 minutes) to reboot the microprocessor. if no resolution, look for a new board part # bp94-01859f if your model # ends in WX
Posted on Dec 07, 2008
You may have a colorwheel going bad. The bearings start going out and this is an indication of the failure. The colorwheel is located in the light engin e therefore you may want to get a qualified tech to look at it
Posted on Dec 16, 2008
use mode button to go back factory settings its in manual page 16 and page 53 if you need manual follow this link to it http://www.samsung.com/us/support/download/supportDownDetail.do?group=&type=&subtype=&model_nm=HL-R5067W&language=&cate_type=all&mType=UM&dType=D&vType=&cttID=260039&prd_ia_cd=&disp_nm=HL-R5067W&model_cd=&menu=download&menu2=detail
Posted on Apr 16, 2009
Here is the procedure for resetting the lamp timer.
This is a quick reference guide to show you how to reset your Samsung DLP TV’s lamp hour meter or hour counter. Resetting the counter is a very simple procedure.
Begin with the TV powered off.
Point your remote towards your TV.
Mute + 1 + 8 + 2 + Power.
Your TV set should now say “Loading Factory”.
Browse down to “Option” then press Enter (or the right cursor button).
NOTE: The Mute+1+8+2 buttons needs to be pressed down consecutively and fairly quickly. If your TV does not enter the service menu after using this combination, you can substitute MENU instead of MUTE. This seems to work for some sets. Also, the right cursor arrow also acts as the ENTER button, so try it if you’re having difficulty with the ENTER button.
To exit the service menu, hit press the EXIT button or just turn off your TV (remember not to turn on your TV immediately afterwards!).
I hope this information allows you to resolve this issue.
If I have helped you, please help me, and rate this suggestion the highest FixYa rating. (Two Thumbs Up) If you cant rate this post with the highest rating, then please comment to this post and I will try to help you further.
Posted on Jun 01, 2009
Tips for a great answer:
Aug 19, 2010 | Samsung HLR5667W 56" Rear Projection HDTV
May 18, 2010 | Samsung HLR5667W 56" Rear Projection HDTV
May 08, 2010 | Samsung HLR5667W 56" Rear Projection HDTV
Jan 08, 2010 | Samsung HL-R5667W 56" HDTV
Apr 15, 2009 | Samsung HL-R6168W 61" HDTV
Jan 13, 2009 | Samsung DLP HL-P5663W 56" TV
Dec 16, 2008 | Samsung HL-R5667W 56" HDTV
Aug 12, 2008 | Samsung DLP HL-P5663W 56" TV
Jun 21, 2008 | Samsung HL-R5677W 56" HDTV
Sep 23, 2007 | Samsung DLP HL-P4663W 46" Rear Projection...
129 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: