Question about Xerox CopyCentre C123 Copier

1 Answer

How do I turn off copy-card default on xerox copycenter c123

Our old library copier (Xerox CopyCentre C123) is not connected to network. It used to be connected to copy-card reader. We wish to now simply use it as upstairs copier for staff.

Posted by Erik Wilkinson on

Ad

1 Answer

PRLandreth

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 17 Answers

Http://www.support.xerox.com/support/copycentre-c123-c128/support/enus.html

This is how to turn off Auditron but this is the same menu as "foreign interface device" or copy card.

Posted on Jan 22, 2014

Ad

5 Related Answers

Anonymous

  • 126 Answers

SOURCE: Xerox Copycentre C123 Creating a Ghost Image

First place an original on glass and make a copy -- mark #1. With that same original on the glass, move the exposure all the way light and make a copy -- mark #2. Again with the same original on the glass, move the exposure all the way dark and make a copy --- mark #3. Place #1 in the middle so the the copies read --- #2, #1, #3. The #2 should be the lightest and #3 being the darkest. If #2 is darker than #3 you have a developer problem and you need to call for service. If #1 and #2 are bad and #3 is a good copy your machine probably just needs a good cleaning, mainly the optics and charge units. If all 3 copies are still poor with the speckles, your are looking at the PCU ( photo conductive unit) also called the drum unit. You can order this unit online -- it is a customer replaceable item.

Posted on Jan 04, 2009

Ad

Rick Kasper

  • 2072 Answers

SOURCE: Need to establish PIN/Code for machine - help xerox c123

The following information describes how to register userIDs and usernames, login names, and passwords for authenticating accesses attempted through the network for scanning services, and impose restrictions on the maximum number of pages to be copied or scanned. Up to 500 user accounts can be registered.
NOTE: You must be a System Administrator to perform this solution.

  1. Press the [Log In / Out] button on the Control Panel. The Login screen will be displayed.
  2. Enter the System Administrator userID using the numeric keypad on the Control Panel, or select the [Keyboard] button on the Touch Screen to enter the userID, and then select [Save] on the Touch Screen.
  3. If necessary, enter the System Administrator password using the numeric keypad, or select the [Keyboard] button to enter the password, and then select [Save] on the Touch Screen.

    NOTE: The default userID is 11111, and the default password is x-admin (must be entered in lower case). If the userID and / or password have been forgotten, a service call must be placed.

  4. Select [Confirm] on the Touch Screen. The System Administrator Menu screen will be displayed.
  5. Select [System Settings]. The System Settings screen will be displayed.
  6. Select [Login / Auditron Administration]. The Login Setup / Auditron Administration screen will be displayed.
  7. Select [Create / Check User Accounts]. The Create / Check User Accounts screen will be displayed.
  8. Select a user account number or use the numeric keypad to enter a user account number in the Go to (001-500) field.
  9. Select [Create / Delete]. The User Account screen will be displayed.
  10. Enter a userID using the keypad on the Touch Screen, and then select [Save]. The Create / Delete screen will be displayed.
  11. Select from the following options:
    • UserID: Allows a userID to be entered using the keyboard on the Touch Screen. Up to 32 alphanumeric characters can be entered including spaces.
    • User Name: Allows a username to be entered using the keyboard on the Touch Screen. Up to 32 alphanumeric characters can be entered including spaces.
    • Password: Allows a password to be entered using the keyboard on the Touch Screen. 4 to 12 alphanumeric characters can be entered. The Password button is also displayed if a password was selected on the Login Setup / Auditron Mode screen.
    • Remote Login Settings: The following settings can be modified on this screen:
      • Login Name - Allows a login name to be programmed that needs to be entered when the machine is accessed through the network.
      • Password - Allows a password to be programmed that needs to be entered when the machine is accessed through the network.
    • Account Limit: Select [Copy Service] or [Scan Service], and then select [Account Limit]. Using the numeric keypad on the Control Panel, specify and restrict the maximum number of pages to be copied or scanned for the account. The maximum number can be entered within the range of 1-9,999,999 pages.
    • Reset Total Impressions: Deletes all data tracked for the selected account.
    • Reset Account: Clears all settings and data for the selected account.
  12. Select [Save].
  13. Select [Close] three times.
  14. Select [Exit].

Posted on Jan 08, 2009

Rick Kasper

  • 2072 Answers

SOURCE: My Xerox Copy centre C123 shows error code 124-315

Thats a weird one. The machine is detecting the wrong speeds.
Try this.

  1. Enter Diagnostic Mode ( UI Diagnostic Mode).
  2. At the Control Panel, press and hold the 0 key for 5 seconds, then press the Start button while still pressing the 0 key.
  3. Press buttons 6, 7, 8, and 9 on keypad and press Confirm.
  4. Press the Log In/Out button (button with Key symbol) on the Control Panel.
  5. Select System Settings.
  6. Select Common Settings.
  7. Select Maintenance/Diagnostics.
Then look at these 3 locations and see if they match, If they do not set them to match the machine speed.
  • [700-600]
  • [700-601]
  • [700-602]

Posted on Feb 11, 2010

Testimonial: "Thankyou,and need more help. chose NVM read/write & enter value700-600, it shows 65000 current value what should i enter as new value?"

wrinaldo

Whit

  • 185 Answers

SOURCE: CopyCentre C123 Copier Copier: CODE 116-331...

It may be a defective Main System Controller board 160K91660 or Hard Drive 960K01120.

There is a diagnostic which requires the Xerox Technician's Laptop to test the Hard Drive.

You might get lucky just reseating the Hard Drive.

Whit
Item, Inc.

Posted on Aug 17, 2010

Aphexenator

  • 54 Answers

SOURCE: error U4-1000 (Xerox CopyCentre C116 copier)

U4-1000 Indicates Fuser on time failure

Follow these steps:

1. Check for paper on the fuser.
Y remove paper N proceed to step 2
2. Check the installation of the fuser assembly, make sure it is securely installed.
Y reinstall fuser N proceed to step 3
3. Remove the fuser. Check the conductivity of the contact points of the thermostat, are the contact points connected
N replace the fuser

Posted on Apr 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I do a password for the machine Xerox CopyCentre C128


Click on the link below and select to view the Xerox CopyCentre C128 owners manualm inside the manual will show you how to set the password

http://www.support.xerox.com/support/copycentre-c123-c128/documentation/enus.html

Dec 19, 2010 | Xerox CopyCentre C128 Black and White...

1 Answer

CopyCentre C123 Copier Copier: CODE 116-331...


It may be a defective Main System Controller board 160K91660 or Hard Drive 960K01120.

There is a diagnostic which requires the Xerox Technician's Laptop to test the Hard Drive.

You might get lucky just reseating the Hard Drive.

Whit
Item, Inc.

May 17, 2010 | Xerox CopyCentre C123 Copier Copier

2 Answers

My Xerox Copy centre C123 shows error code 124-315 pls help


Thats a weird one. The machine is detecting the wrong speeds.
Try this.

  1. Enter Diagnostic Mode ( UI Diagnostic Mode).
  2. At the Control Panel, press and hold the 0 key for 5 seconds, then press the Start button while still pressing the 0 key.
  3. Press buttons 6, 7, 8, and 9 on keypad and press Confirm.
  4. Press the Log In/Out button (button with Key symbol) on the Control Panel.
  5. Select System Settings.
  6. Select Common Settings.
  7. Select Maintenance/Diagnostics.
Then look at these 3 locations and see if they match, If they do not set them to match the machine speed.
  • [700-600]
  • [700-601]
  • [700-602]

Feb 11, 2010 | Xerox CopyCentre C123 Copier

1 Answer

Gives an error code 062-277


You will have to call in a xerox tech, it seems that one of the boards on the scanner is u\s

Apr 13, 2009 | Xerox CopyCentre C123 Black and White...

1 Answer

Schematic of the Xerox XC865


google The Parts Drop, Give them a call, ask for Britt he can help you most likely.

Mar 10, 2009 | Xerox CopyCentre C123 Copier

1 Answer

Set PDF Format as default on scanner


Yes you can,you just select the settings in the e-mail settings to scan to pdf,Wat is the make and model of the copier?

Feb 19, 2009 | Xerox CopyCentre C123 Copier

1 Answer

Cracked fuser drive gear for Xerox copier XC865


There is a metal clip that holds it on the roller. Look in the machine for it.

Jan 31, 2009 | Xerox CopyCentre C123 Copier

1 Answer

Copying with a copycentre 255


Go to www.xerox.com , on the home page click Support and Drivers.
IN the search where it asks for a product name or number type in 255.
Then select the Copycenter 255 Documentation.
Then select either the QUick reference guide, which is most likely all you need. or download the training and information program.

Jan 01, 2009 | Xerox CopyCentre C123 Copier

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

docukaaf

Level 1 Expert

38 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...