Question about Whirlpool Washing Machines

1 Answer

Whirlpool frontlaoding washing machine AWM 8121- spin speed drop to 0 when washing

Spin speed drop to 0 when washing and water does not goes through detergent box

Posted by vinh an tran on

Ad

1 Answer

john

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Whirlpool Expert
  • 517 Answers

Change motor brushes

Posted on Jan 12, 2014

Ad

2 Related Answers

Anonymous

  • 49 Answers

SOURCE: Whirlpool 6th Sense AWM 8121

it will either be the wash motor capacitor or the wash motor brushes. both of witch will have to be tested by an electrician

Posted on Aug 18, 2008

Ad

Anonymous

  • 3 Answers

SOURCE: I have a whirlpool front

Probably needs a new "mother board." I've had to replace mine 3 times. It's expensive too.

Posted on Dec 28, 2008

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool awm 8121 leak


down by the water solenoid those leak sometimes or a loose hose if you cant fid it it might also be the seal in the drum

Aug 25, 2014 | Washing Machines

1 Answer

I have a whirlpool awm 8121 6th sense front loader. when i select the cycle, usually rapid, and press the start button the machine commences to fill with water. when it comes time for the actual washing...


If your machine is reasonably old, perhaps take a look at the bushes of the motor . Before that, take the manual and run the test cycles by following the instructions; it might provide you with answers

Oct 14, 2017 | Whirlpool AWM8123 Front Load Washer

1 Answer

Front loader whirlpool washing machine won't go thru cycles.


"o" is an unsual code. usually it will have an "f" then a number. it may be that you are having a draining issue. is the unit full or have some water left in it? if so take off the front panel and see if you can remove the sump cover. be ready for water to come out, then remove whatever is blocking the pump and sump area. it most liekly has lint or items in there causing no drain.

Dec 28, 2008 | Washing Machines

1 Answer

AWM 8121 NOT DRAINING OR SPINNING PROPERLY


that isn't a good model number,open the door,look around the opening where you put the clothes in and next time send the model number off of the machine,if you can't get it to drain and water is in the machine get a shop vac,suck out the water from the tub,then go to the pump,loosen the center of the pump until water starts to come out vac it up until no more water comes out,remove the center catch and see if there's junk in there,if so this is your problem,stick the nozzle of the vac inside and clean out the inside,put it back together and see if it will drain

Sep 29, 2017 | Whirlpool AWM6120 Front Load Washer

1 Answer

Washing cycle starts and takes hours even for short cycle.


Try checking for good water supply.
Pull out detergent tray and check for good water supply during filling.
if poor filling-
Try checking the hoses.
Turn taps off, disconnect from machine, place hose end in sink, turn tap on and check for good water flow.
if the hose has a red indicator in the side of the hose (end which is fitted to the tap) - Red indicator is a failed hose.(for models with Water Stop hose type "B")

Oct 05, 2008 | Whirlpool AWM6120 Front Load Washer

3 Answers

Whirlpool 6th sense front loader awm 8121


my whirlpool 6th sense will not start all lights and power i think that it is the door sensor at fault? The green light door locked light is not on.

Jul 18, 2008 | Whirlpool AWM6100 Front Load Washer

2 Answers

HI, I am having a lot of trouble with my front loader which is only about 4 years old. It seems to become very unbalanced during the coloured wash setting (even with a small load) - and yet is perfectly...


check teco coil on the back of the motor, it may have come loose'its about inch round thing it gives power to the the speed control module circuit board thats why its tumbleing too fast.bye Eamonn Ireland

Jun 11, 2008 | Whirlpool Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Brad Brown

Level 3 Expert

18563 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...