Question about GE Nautilus 24" Built-in Dishwasher

1 Answer

GE Nautilus - top spinner has fallen off

The spinning water thing on the top has come off and I can seem to get it reattached to where it stays on.   Any suggestions?  Am i missing a part?



Posted by meilichios on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has answered 200 questions.


    An expert whose answer got voted for 20 times.

  • Expert
  • 249 Answers

The rotor arm may be faulty

Posted on Nov 28, 2007


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Our Kenmore top load model 22422 started having problems with the spin cycle. Once it gets to the spin cycle, it makes a terrible grinding like noise - it is not spinning. However it will drain if you let...

The double shaft motor does double duty. One direction for wash and another direction for spin. In wash mode the water stays put in the tub because the pump is running backwards. In spin mode the motors turns in opposite direction. This pumps the water out and spins the clothes dry. From what you have described the drive coupler is toast.
This video shows how to swap the drive couple out:



If you need further help, reach me via phone at

Mar 01, 2011 | Kenmore 22422 Top Load Washer

2 Answers

Whilst on the rinse cycle, it just keeps on filling with water and does not stop. If I am out, it is just waisting water all of a sudden. I have to physically turn the dial to Spin for it to stop filling...

Easy fix, no parts needed mate. Simply look for a loose hose going to the water level switch. The small vacuum hose from tub to switch vibrates off from time to time OR sediment gets into the tube where it attaches at the base of the tub. Remove the hose at the switch in the control console and blow through it to clear any blockage and reattach firmly. Remove the water and retry. With any luck the washer will resume normal duty's. Good Day!

If you need further help, reach me via phone at

Jan 11, 2010 | Speed Queen AWS75NW Top Load Washer

1 Answer

I have a Maytag Neptune front loading washer. Why does water remain in the drum after all cycles completed?

This depends on whether all the water is not being drained out or if additional water is being allowed in. The first thing to check is that the drain line is not kinked or obstructed. I would also suggest running a hot wash cycle with 1/2 cup of vinegar. This will help clean out any sludge build-up in the drain lines. The pump can be checked if this does not cure the problem. Unplug the machine, turn off the water, and remove the hoses from the pump. Use a flashlight to look into the suction port to make sure nothing is clogging the pump, like the occasional stray sock, etc.,and check the pump impeller. Be sure that no blades are missing or broken and that the pump impeller spins freely. If any blades are missing/damaged or if you can't get the impeller to spin freely the pump would be defective. These are some items to consider if the machine is not getting draining all water.
If however, it seems to be removing all the water, but additional water seems to be accumulating after the fact, then check the water inlet valve solenoids. They can be tested using a multimeter or ohmmeter and checking continuity. A lack of continuity will mean a bad solenoid. These are some things to consider and I am really sorry for your trouble. I hope this helped and best wishes.


Oct 03, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Machine won't spin... Machine gets water,

only be one thing, the wig-wags are not shifting transmission into spin if everything else seems ok in operation

Aug 23, 2009 | Washing Machines

1 Answer

Admiral Top Load Washer Model LNC6762B71 overflowed

Remove the control console cover. Find the water level switch.
It has a small tube attached to it.
Remove the tube and blow air through it. It is probably stopped up. Reattach it to the water level switch.
Look over the length of the tube and may sure it is not pinched.
Set the washer to spin and run spin for about 1 minute.
Then run water on a lower level and see if it shuts off.
If not replace the water level switch.

Feb 28, 2009 | Admiral AW22 Top Load Washer

1 Answer

Kenmore top loading washing machine irratic spin cycle

Check the Vibration damper rods to be sure that...
1. They are there and mount is solid.
2. If they are broken in 1/2.
3. The plastic knuckle mounts are not missing/broken.
4. There is oil in the shock absorber/spring section of the rods.

Also - there are suspension springs on the bottom of the tub that could be broken and/or missing.

Replace/repair as necessary.

P.S. If you installed yourself - be sure you removed the shipping pins at the bottom of the machine.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Feb 16, 2009 | Kenmore Washing Machines

1 Answer

Water Dispenser for Frigidaire

try mashing the wire end connector gently with a pair of pliers to tightn the connectorer and let me know if it stayes on

Jan 15, 2008 | Frigidaire FRS26R4A Side by Side...

Not finding what you are looking for?
GE Nautilus 24" Built-in Dishwasher Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers


Level 3 Expert

4369 Answers

Bill Johnson

Level 2 Expert

306 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides