Question about Jura Capresso Impressa X7 Espresso Machine

Open Question

Impressa x7 empty drip tray message when drip tray is empty

Posted by Anonymous on

Ad

5 Related Answers

RB5193

  • 4 Answers

SOURCE: Tray empty message

If the machine says TRAY MISSING it's the contacts at the back so clean as other people have stated, you can also use a cardboard nail file to clean the contacts at the back if there really skanky!.

If the machine keeps saying EMPTY GROUNDS even though you have, pull out the tray, look just inside the aparture where the tray goes top right at the front there is a small slot where if you look closely you can see a small white micro switch. This will be probably gunged up with coffee and the switch will be stuck up, get a can of WD40 and squirt a small amount up into the switch then poke the switch with a small screwdriver up and down until it moves smoothly.

Then replace all the bits, sit down, look smug and have a coffee cos you've fixed it!! :0)

Posted on Oct 13, 2009

Ad

RB5193

  • 4 Answers

SOURCE: impressa z5 grounds empty will not reset even

If the machine says TRAY MISSING it's the contacts at the back so clean as other people have stated, you can also use a cardboard nail file to clean the contacts at the back if there really skanky!.

If the machine keeps saying EMPTY GROUNDS even though you have, pull out the tray, look just inside the aparture where the tray goes top right at the front there is a small slot where if you look closely you can see a small white micro switch. This will be probably gunged up with coffee and the switch will be stuck up, get a can of WD40 and squirt a small amount up into the switch then poke the switch with a small screwdriver up and down until it moves smoothly.

Then replace all the bits, sit down, look smug and have a coffee cos you've fixed it!! :0)

Posted on Oct 13, 2009

Ad

Anonymous

  • 3 Answers

SOURCE: Jura Impressa F50 - tray - fault 8

Hi, if you havn't already solved this one, it has been caused by pulling the drip tray/ dump box out while the brew unit was still active. Switch off the machine and insert the drip tray without the dump box. Turn the machine back on and the brew unit should re align itself.

Posted on Feb 19, 2010

CKinAZ

  • 1 Answer

SOURCE: I was going through the decalcifying process and

I had the same problem and had success with cleaning the contacts in the back of the machine with a small nail file/emery board. I found that the contacts that are inside the machine had a little calisification on them. Once they were cleaned up no problem.

Posted on Oct 24, 2010

Andrew

  • 1 Answer

SOURCE: I have a Jura Capresso Impressa S9 and it keeps

Where the contacts attach to the drip tray on the inside is where I had some coffee ground "sludge". It was making a weak electrical connection between the two contacts. As soon as I took a fine scrubber sponge to get rid of the build up - the Empty Tray message went away when I put the tray back in.

Posted on Oct 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Message 'Empty trays constantly displayed, although trays were emptied


Xerox Workcentre 7855 Bypass Tray 5 empty - Customer Support Forum

forum.support.xerox.com/t5/Hardware/...Tray...empty/td.../14901...
XeroxSep 29, 2014 - All my 7855 have the Tray 5 (Bypass) is empty. message. .... as there is no paper in it the message will always be displayed in the driver here:. Error message-Paper Tray is empty
Dec 8, 2011
Phaser 3600 reports as paper try empty
Oct 20, 2011
8560 waste tray error
Dec 13, 2010
More results from forum.support.xerox.com

empty drip tray Questions & Answers - Fixya

www.fixya.com > Forum > Tags
But now the display shows "Empty the drip tray" constantly. ... Empty Drip Tray message Getting the message "Empty Drip Tray" even when the tray is completely .

Nov 21, 2015 | Office Equipment & Supplies

1 Answer

Jura impressa x7 keep getting report fill water tank


make sure the water tank is full! there is a small float in the tank that moves up and down near the bottom, make sure this is up and not stuck down.

Feb 05, 2014 | Capresso Jura Impressa X7 220v

1 Answer

Error report fill water tank


small black rectangular float is stuck in the water tanks . take off tank and empty. then shake you will see it on the side wall (machine side) if it does not rise when water is filled the machine still thinks its empty

Feb 05, 2014 | Jura Capresso Impressa X7 Espresso Machine

1 Answer

I just went thru the entire decalcifying process and got to the final step, emptied the drip tray and coffee grounds bin, put the tray back into place, but can't get the display off of "empty...


You should Clean and dry the metal contacts on the back of the drip tray, ensuring that the gap between the contacts is clean and dry (if present, contacts not on all JURA models) Make sure that the plastic in between the contacts is clean

Sep 13, 2011 | Microwave Ovens

1 Answer

Message says tray missing, even with tray in place. Have found the micro switch inside and pushing this down "fools" the machine into thinking the drip tray is back in place, but then when the...


Clearly, the drip tray is not aligned right, or there is a manufacturing flaw. Simple answer would be to examine the part of the tray that you believe is supposed to engage the switch when it is in place, and try to figure out why it is not doing this.
Personally, if you are like me and don't mind voiding a warranty, I'd suggest removing the switch so the machine always thinks the tray is in place.

May 07, 2011 | Jura Capresso Impressa F7 Espresso Machine

1 Answer

I was going through the decalcifying process and the message "empty tray" displayed (Jura Compresso Impressa S8). I removed the tray, cleaned it, replaced it, but the message remains as "empty tray" and I...


I had the same problem and had success with cleaning the contacts in the back of the machine with a small nail file/emery board. I found that the contacts that are inside the machine had a little calisification on them. Once they were cleaned up no problem.

Aug 15, 2010 | Jura Capresso Impressa S8 Coffee Maker,...

1 Answer

Jura Impressa F50 - tray - fault 8


Hi, if you havn't already solved this one, it has been caused by pulling the drip tray/ dump box out while the brew unit was still active. Switch off the machine and insert the drip tray without the dump box. Turn the machine back on and the brew unit should re align itself.

Feb 15, 2010 | Jura Capresso Impressa F9 Espresso Machine

5 Answers

Tray empty message


If the machine says TRAY MISSING it's the contacts at the back so clean as other people have stated, you can also use a cardboard nail file to clean the contacts at the back if there really skanky!.

If the machine keeps saying EMPTY GROUNDS even though you have, pull out the tray, look just inside the aparture where the tray goes top right at the front there is a small slot where if you look closely you can see a small white micro switch. This will be probably gunged up with coffee and the switch will be stuck up, get a can of WD40 and squirt a small amount up into the switch then poke the switch with a small screwdriver up and down until it moves smoothly.

Then replace all the bits, sit down, look smug and have a coffee cos you've fixed it!! :0)

Nov 15, 2008 | Jura Capresso Impressa Z5 Espresso/Coffee...

Not finding what you are looking for?
Jura Capresso Impressa X7 Espresso Machine Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jura Capresso Coffee Makers & Espresso Machines Experts

The Knight
The Knight

Level 3 Expert

76407 Answers

markybean

Level 1 Expert

41 Answers

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Are you a Jura Capresso Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...