Question about Biostar Computers & Internet

1 Answer

No video after power up biostar t series MOBO w/ Semprem cpu

After install semprom cpu to biostar T series motherboard and power up..no video, after clear CMOS still no video, please help.

Posted by kahuff1991 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I was installed xp sp2 but vga driver & multimidia driver not installed

Posted on May 25, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have bought 2 Biostar N68S motherboards for HTPC builds. Both of them have the same CPU and RAM. Neither of them will show any VGA output, despite being hooked up to different screens. The other...


The motherboard has a AM2+/AM3 socket, and the processor is AM2, while there is some compatibility between AM2+ and AM2 sockets, it is not guaranteed, so this could very likely be your issue.

Jul 23, 2011 | Biostar N68S NVIDIA MCP68S Socket AM2+/AM2...

1 Answer

P4M2PROP motherboard have power but not working???


The first step would be to clear the CMOS ram manually. To do this, you need physical access to the mother board.

- Make sure the power is off but do not unplug from power.
nyctobello.jpg
- Locate Clear CMOS (JBAT) Jumper. From above, lower right hand corner.
- Simply remove the jumper and put it back again.
- Power up.
- If problem persists:

- May be faulty ram
- If you have a video card installed, uninstall it and connect monitor to VGA port of motherboard. It could be a faulty video card.
- CPU could be over heating, clean with compressed air, check fans and CPU grease.

Hope this helps...

Jul 04, 2011 | Computers & Internet

1 Answer

Please clear cmos if system no display after overclocking


Click the following picture to enlarge:
pctech1_0.png

CPU Overheated
If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.

Or you can:
1. Clear the CMOS data.
2. Wait for seconds.
3. Power on the system again.

If after clearing the CMOS you still have no display, you may have damaged your motherboard, CPU, or RAM. If you need further assistance with this Motherboard, let me know.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Mar 25, 2011 | Biostar G31-M7 TE Motherboard

1 Answer

Biostar u8668 grand does not power up when agp


Good Day sir, try to check the CMOS/BIOS setup, and go look for Initial Display First, there are several options, Onboard / AGP / PCI. OR, after you remove your AGP, clear the CMOS/BIOS setup. find the jumper wire near the battery this sets your motherboard to factory setup and uses the onboard VGA. test the pc without the AGP.

Oct 18, 2009 | Biostar U8668 Motherboard

2 Answers

No POST No Beeps


hi,,,

i think your problem sir is the Bios ,,

1: after trying to clear the CMOS, you can check the manual for that,,,

if not ,,

2: please just try to replace it with an updated one from another exact Mainboard ,,,

i think it will work perfectly :)

thankx very much,,,,

Apr 16, 2009 | Biostar P4M800 Pro-M7 Socket 775 mATX MB...

1 Answer

Singlle long beep on booting up my Biostar M7NCDPro motherboard with nothing on screen


If you get one continuous beep (Long and Non-Stop)
This could happen if:
1. The Power supply is damaged or bad.
2. The BIOS is corrupted. Try resetting the CMOS using JCMOS1 jumper on the motherboard or remove the battery from the motherboard for 20 minutes. At this point the first thing to try is a different Power Supply to see if the result is better. If the same problem happens with the new power supply, you may need to send the BIOS Chip to local dealer for reprogramming.

If you get one long High Pitched tone that does not stop until you disconnect the power supply:

1. Check if the CPU fan is connected to the JCFAN1 connector.
2. The CPU might be overheated. Change the CPU FAN or check if the CPU fan has proper contact with the CPU. Refer to your manual for CPU installation.
3. Clear CMOS battery (JCMOS1), be sure to set JCMOS1 back to 1-2 position. (See Quick start guide/ user manual for more info on how to clear the CMOS)
4. Make sure the power supply you have on your system supports the M/B specification. Example. If you have a P4 M/B, you need to use an ATX v2.03 specification power supply. (power supply that has an extra 4-pin square connector)

Sep 15, 2008 | Computers & Internet

1 Answer

Problem with my BIOS CMOS Setting


Its due to your default CMOS setup does not match with your CPU configuration especially with CPU speed.
  1. To fixed the above problem goto BIOS and navigate settings of CPU, speed etc. Set the speed with the proper value as per manual. And save the settings.
  2. Infuture when you will load default, at that time also set the CPU settings.
  • The CMOS battery might not be connected properly or may be its not producing enough power as per needed by board. So have a look with another battery. Also clean the connection point of the CMOS battery.

Good Luck
Iqbal

Apr 22, 2008 | Biostar P4M80-M4 Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Biostar Computers & Internet Experts

Jayburt

Level 2 Expert

89 Answers

Ekse

Level 3 Expert

13434 Answers

Lee Hodgson
Lee Hodgson

Level 3 Expert

4810 Answers

Are you a Biostar Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...