Question about Konica Minolta bizhub 250 All-In-One Laser Printer

1 Answer

C0991 error on bizhub c350

Bizhub c350 paper lift on tray 3

Posted by Anonymous on

Ad

1 Answer

Norman J Weimar Jr

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Konica Minolta Master
  • 6,960 Answers

Check the gear assy behind the front cover of the bottom draw

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Posted on Jul 04, 2016

Ad

5 Related Answers

Anonymous

  • 589 Answers

SOURCE: copier malfunction

Code C0F36 is a low toner density error on the black developing unit.

Was it asking for black toner before this code appeared?

Posted on Feb 10, 2008

Ad

Anonymous

  • 3 Answers

SOURCE: Konica Bizhub Password Reset

Konica Bizhub c350 default password is 12345678 give that a try

Posted on Mar 17, 2009

rylee_smith

Rylee Smith

  • 8619 Answers

SOURCE: COF36 error on a Bizhub C350

Hi

C0F36 error means abnormally low toner density detected Black ATDC Sensor. Check for the black toner and try reinstalling the cartridge if replaced already. And if the toner crtridges are empty then replace the cartridge.

Please do rate this solution as FixYa and revert for further assistance.

Thanks
Rylee

Posted on Apr 21, 2009

firecontrol7

Norman J Weimar Jr

  • 6960 Answers

SOURCE: KONICA MINOLTA BIZHUB C350 WITH ERROR CODE C0960

Check your bypass tray, the tray is on the right side of the machine, the tray flips out for legal and 11x17 paper sizes. Check that there is nothing jamed inside, code says that the tray can't lift. so check for anything jamed inside down there. As to reset the code open then close the front door where you put the toner. Turning the machine on and off will not reset the code. but open and closing the front door will clear about 80% of the service codes.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Posted on Jul 25, 2009

steve p

  • 44 Answers

SOURCE: on the bizhub C550 an error code C0204..... won't

Two things 1) check to see if there is paper in the back of the of the tray where it meets the back wall (that would prevent the paper tray from rising. 2) there is an upper limit sensor on the paper feed (thats where the rollers are) so check to see if any bits of paper blocking the sensors. If you find it, reset the machine and it will see the tray.

Posted on Dec 14, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

KONICA MINOLTA BIZHUB C350 WITH ERROR CODE C0206


C0206
Tray 3 feeder up/down
abnormality
• The tray 3 upper limit sensor is not blocked
even after the lapse of a given period of time
after the lifting motion has been started.

Jul 15, 2014 | Konica Minolta bizhub C351 All-In-One...

1 Answer

BIZHUB C350 ERROR CO206


C0206
Tray 3 feeder up/down
abnormality
• The tray 3 upper limit sensor is not blocked
even after the lapse of a given period of time
after the lifting motion has been started.

Jul 15, 2014 | Konica Minolta bizhub C250 All-In-One...

1 Answer

Konica minolta c350 error c0204


Tray 2 Feeder UP/Down abnormality.
2nd Tray Lift-up motor (M9) is problematic.

Jul 07, 2014 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

C0991 error on bizhub c350


the third paper draw

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Dec 30, 2013 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

Error CO202 Bizhub


C 0202 - 1 st tray lift up failured.
Remove the 1 st tray,in the right side located 1 screw and in copier is a paper when blocated the tray lift gear.Remove the misfed paper and push in the tray ,open and closed the right door and the copier must be ready.
C 0204 - 2nd tray
C 0206 - 3 rd tray
C 0208 - 4th tray
C 0211 - bypass tray
Good luck.

Feb 14, 2013 | Konica Minolta PRINTING - Bizhub-250...

2 Answers

How do you clear error code on a bizhub C350. A piece of paper was fused on the fuser unit and we were able to get the paper off. Now we have no access because the panel is locked.


while powering up machine hold down utility/counter key until trouble reset appears on screen. select it and ok should apper under it. power down machine for atleast 10 sec and turn machine back on.

Jul 22, 2011 | Konica Minolta bizhub 350 All-In-One Laser...

1 Answer

Error code c-0960 how can i reset it


C-0960 error code is for the bypass tray on a C350 copier. Make sure there is nothing binding up the tray lift mechanism. To reset open the front door, on the right side where the plastic starts to curve you will find a small hole, in that hole there will be a small button. Use a pen tip or a paper clip to press this button, this will reset the error. If the error returns there may be damage to the bypass lift system.

Apr 12, 2010 | Konica Minolta bizhub 350 All-In-One Laser...

3 Answers

Bizhub C350 Malfunction Code C-0510


I have this malfunction code, C-11A3, coming up on my Konica/Minolta Bizhub 350 copier/printer. Anyone know what it is? I don't use the techs, because they charge much I don't pay for the service anymore-seems like most things should be able to be fixed by the owner. I needed help for this code

Mar 21, 2009 | Konica Minolta bizhub C250 All-In-One...

Not finding what you are looking for?
Konica Minolta bizhub 250 All-In-One Laser Printer Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers

carpediemweb

Level 1 Expert

54 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...