Question about Panasonic CQ-C1100U CD Player

Open Question

Panasonic cq-c1100 u car am/fm/cd

Poor am/fm but great cd sound; When I trry to adjust antenna , I get excellent only when my wrench touches the mast or securing bolt

Posted by chan14 on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Speaker makes a popping sound when car starts

may be the antenna jack such is connected in cassete is n't good

Posted on Jul 09, 2007

Ad

Anonymous

  • 75 Answers

SOURCE: panasonic cq-c1323nw reset button

hi there type your model number into this link and you can download the user manuall, i've tried it for your model no and it works.
http://www.panasonic.co.uk/html/en_GB/220239/index.html#anker_220239

Posted on May 02, 2008

Ad

Anonymous

SOURCE: No sound from CQ-1305U car CD/stereo

connect the panasonic power antenna lead to a power wire

that should do it.

Posted on Jul 07, 2008

Anonymous

SOURCE: Panasonic CQ-DF903U How do I hook up my Sirius Radio to it?

Sirius radio connects via a special dock. Sorry, but you're screwed with your XM unit...

Posted on Jul 10, 2008

Anonymous

  • 1 Answer

SOURCE: set time car radio/cd Panasonic CQ-C13367

First of all, go to service.us.panasonic.com/operman to get the manual for your unit.

With the unit turned on and the clock displayed, pres disp for more than two seconds. The hours will blink... press < or > to adjust hour. Press disp again, the minutes will blink... press < or > to adjust minutes. Lastly, press disp to store the correct time. Good Luck!!!

Posted on Nov 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove broken antenna from 1999 ford forte


No Most power antenna work the same. it takes two people to change them. watch and listen as radio is turn on then off do this several times then remove retainer nut turn radio on and assist removal of remaining mast watch where the teeth are located in motor assembly. fully extend new antenna mast lube with machine oil 3 and 1 works great then slowly feed new mast into motor assembly then turn radio off as you guide new mast down install retainer parts work antenna up and down overrun clutch will make the final adjustment.

Nov 09, 2013 | Ford Cars & Trucks

2 Answers

Radio static


Check your antenna. If the mast is not extended, your reception will be limited. try an AM station, usually a local AM station will still come in even with the mast down. Have you tried playing a CD (if equipped) ? If that plays well, you've confirmed lack of reception as the problem. If the mast is extended and you still do not have reception, the antenna plug my have come out of the back of the radio. The requires removing the radio to check.

Sep 30, 2013 | 1997 Honda Accord

1 Answer

Where is the radio Antenna located?


Mercedes Benz Antenna Mast The upright support that also serves as proper anchorage to your car antenna is your Mercedes Benz antenna mast. Located right at your vehicle's fenders, it is the part responsible in providing a clear and uninterrupted radio station reception you grew accustomed to enjoy while hitting the road. Providing your expensive audio system or car stereo with cool sounds of up to a hundred AM/FM radio stations to choose from, driving boredom is a thing of the past. Because your Mercedes antenna mast is definitely among the least overlooked part for maintenance, damages to the part will be due to neglect. Forgetting to track down or put down the car antenna when submitting your vehicle to automated car washing house could seriously damage the part. Good thing precision fitting replacements to damaged stock part are conveniently available to instantly get back the service offered by the mast.
mb_antenamast.jpg
Daily driving will be a breeze when you keep your Mercedes antenna mast on good working conditions. Having your car radio feed you with the necessary weather reports and traffic advisories enables you to avoid hitting on difficult areas where you can virtually get stranded. For a simple device, the sophisticated construction of an antenna mast is crafted durable enough to withstand extremely cold and desert hot climatic conditions. For preventive maintenance, regularly inspect the part for rust formations. Check when connections become loose to avoid having your car antenna from launching out of the fender. Although it is crafted to last, antenna mast replacement is eventually needed due to faultiness which comes with age.
Once your stock antenna mast starts fouling up, your car antenna will simply be inoperable. You might as well consider finding immediate replacement to continually experience the pleasure of driving comfort features Mercedes Benz engineers have crafted for you to enjoy. Invest with precision fitting and quality products that meet precise OEM specifications to ensure product longevity and consistently dependable service. For a trusted source of genuine and great valued Mercedes Benz auto-part replacements, we offer a convenient online shopping store that covers your immediate maintenance needs any time or day. Click on our online catalog to conveniently locate and compare Mercedes Benz antenna mast applications to seal premium deals on your next scheduled replacement.

Aug 16, 2011 | 1999 Mercedes-Benz E-Class

1 Answer

Poor radio reception.I've tried a new aerial mast,no improvement. CD player sounds fine. Any ideas? (Passat Est.2003)


Important! Please give copies to all your VW Technicians C 91--99--07 E 1999 Volkswagen of America, Inc. 1 Subject: Model(s): Group: Number: Date: AM Radio, Poor Reception 1999, 2000 91 99--07 New Golf, New Jetta, Aug. 2, 1999 New Beetle, Passat Condition AM reception is poor. May be caused by: ? An incorrect antenna mast installed for the antenna base equipped with the vehicle ? Poor ground at the antenna base or radio ? Poor battery ground to chassis or engine ? Poor antenna cable connection at Radio ? Corrosion at the antenna coaxial connectors at radio or antenna Service Vehicles are equipped with either a Bosch or a Clarion antenna base mounted on the roof and (for shipping purposes) the appropriate matching mast is located in the luggage compartment. If radio antenna masts are removed from vehicles and stored until vehicles are sold, there is a chance that an incorrect mast can be installed at the time of delivery. Note: Mismatched antenna mast and base will cause poor AM radio reception. The antenna base and mast can be identified visually as follows: (Cont. on Page 2)91-A260 requires gloss finish antenna mast 57mm 49mm Bosch 91-A261 requires matte finish antenna mast 61mm 41mm Clarion 91-A262 Technical Bulletin Important! Please give copies to all your VW Technicians C 91--99--07 E 1999 Volkswagen of America, Inc. 2 Bosch antenna ? Base (although oval) is more circular in shape (approx. 57mm x 49mm). ? Made in Germany stamped on underside of base. ? Two screws on underside of base are unpainted. ? Requires gloss finish antenna mast. Clarion antenna ? Base is more oval in shape than Bosch (approx. 61mm x 41mm). ? Two screws on underside of base are painted. ? Requires matte finish antenna mast. If antenna mast matches the antenna base correctly: -- Check antenna coaxial cable connections --arrows-- for corrosion and clean if necessary (DO NOT apply stabilant). Passat coaxial cable connection for radio is under the carpet on right side of tunnel near shifter. -- Ensure that coaxial cable is firmly seated in radio (Passat cable connection, see previous step). -- Check ground at the antenna below roof Nut --4-- (torque = 7+1 Nm) must firmly secure antenna to roof). (Cont. on Page 3)Technical Bulletin Important! Please give copies to all your VW Technicians C 91--99--07 E 1999 Volkswagen of America, Inc. 3 -- Check ground for radio behind radio on cross member (On Passat models as of Nov. 1998 beginning VIN: XE285000 ground for radio is on right side of center tunnel). -- Check engine compartment ground, left side, below battery tray; frombattery GND to body. -- Check engine/transmission ground on transmission, near engine block. -- If all grounds and antenna mast are OK. -- Replace antenna and coaxial cable assembly

May 06, 2011 | Car Audio & Video

3 Answers

How do you replace the atenna mast for 2005 sierra.


How do I install a new antenna on my GMC 05 2500 Sierra. I have to replace the base because it broke off. I've taken the dash off. But cannot seem to fish wire through the firewall.

Nov 26, 2010 | 2005 GMC Sierra

1 Answer

Poor reception. Changed the radio with another of the same model. Reception is still poor. Must be an antenna problem. How do I go about replacing the antenna and coax?


1. Disconnect negative side of battery.
2. Wait at least 2-minutes to de-energize the airbag system
3. Remove the glove box from the dash.
4. There will be a coax cable towards the top of the opening. Disconnect the antenna cable lead.
5. Remove the right kick trim panel. There should be no screws just clips.
6. Loosen the rubber grommet insulator from the door hinge area. This is a rubber accordian style guard for wires located between the "A" pillar and the door.
7. Pull the antenna cable out of the dash area to the hinge area.
8. Jack up the front right of the vehicle. Support with Jack Stands. Do not use only the Jack! Use the jack as a back-up in case of Jack Stand failure.
9. Remove the right front tire.
10. Remove the right front wheel housing splash shield. There should be 3-push type retainers and one 10 mm bolt below the bumper.
11. Slide the plastic cover (on the base) up on the antenna mast.
12. Use a open end wrench to unscrew the antenna mast at the base and remove the antenna mast.
13. Remove the plastic cap from the base nut on the base and remove the base nut.
14. From underneath the fender: pull down the antenna base. And pull the cable towards you - out from the door hinge area into the fender area.
Good Luck! Installation is reverse of above.
If this helped or you need clarification or additional help: let me know at fixya.com

Nov 27, 2009 | 2000 Dodge Caravan

1 Answer

Replace antenna


Remove old Antenna
  1. Activate the antenna switch to the up position.
  2. Using the wrench or needle-nose pliers, loosen and remove the original retaining nut on the base of the antenna mast.
  3. Gain access to the underside of the area of the trunk where the antenna is located.
  4. Remove the bracket or brace that is below the hole and holding the antenna in place.
  5. Remove the mast.
  6. Find the motor that controls the antenna mast. Generally, power antennas will have a constant 12-volt lead and a ground lead. The ground lead will be grounded to the panel next to the motor.
  7. Remove the ground lead from the panel.
  8. Pull out the antenna coaxial cable.
  9. Unplug the coaxial from the extension coaxial cable.
  10. Remove the original antenna coaxial cable. Note the route the cable follows.

Install new Antenna
  1. Inspect the fender area where the antenna mast will be mounted for rust.
  2. Clean the area before installing the new antenna.
  3. Plug the new antenna coaxial cable to the extension coaxial cable.
  4. Plug the new antenna's coaxial cable into the radio's chassis antenna jack if there is no extension coaxial cable. Tie or tape the string you put on the extension cable to the new antenna coaxial cable. This assures that the 2 cables stay together as you route them to the antenna mount in the fender.
  5. Connect the power lead of the antenna to the power antenna lead on the radio.
  6. Connect the 12-volt constant lead to the antenna to a 12-volt source or to the ignition switch.
  7. Direct the new antenna cable via the same route followed by the original antenna cable on up to the hole in the fender in which the mast will be mounted.
  8. Ground the ground lead from the motor to a clean metal surface on the metal panel near the mount.
  9. Insert the mast into the hole. Face the serrated side of the plastic cable on the bottom of the mast toward the motor side. The plastic cable can be inserted freely to about 12 inches and will stop.
  10. Turn on antenna switch to down position until the plastic cable goes down and catches into the gear mechanism of the drum housing. If the plastic cable does not gear into the mechanism, twist the cable slightly until the cable contacts into the gear mechanism while the motor is in operation.
  11. Stop the motor after the cable goes into the housing 12 to 25 inches.
  12. Secure the bracket or strap to the bottom of the antenna mast and to the metal fender.
  13. Replace the retainer nut to the base of the antenna mast and secure tightly.
  14. Replace the panel that covers the antenna mount area.

Oct 16, 2009 | 1996 Honda Accord

1 Answer

How to replace thunderbird antenna


please rate service.

Automatic Electric Antenna
Removal
  1. Lower electric antenna (18850) .
  1. Remove rear retaining screws of RH front wheel splash shield for access to antenna lower retaining bolt.
  1. Remove lower retaining bolt.
  1. Remove radio antenna nut (18865) from top of motor tube and remove electric antenna through fender/splash shield access.
  1. Disconnect signal cable and motor wire connector(s).
Installation
  1. To install, reverse Removal procedure.
  1. Tighten top radio antenna nut to 6-8 Nm (54-70 lb-in).
  1. Tighten lower electric antenna retaining bolt to 5.8-7.8 Nm (51-69 lb-in).
  1. Check operation of electric antenna and radio chassis .

    Automatic Electric Antenna


    1faf511.gif

mast
Mast, Power NOTE: A power antenna mast which is bent or broken can be replaced without replacing the motor and tube assembly.
Removal
  1. Remove radio antenna nut (18865) and radio antenna stanchion (18919) .

    ssd~us~en~file=l6389b.gif~gen~ref.gif

  1. Loosen retaining nut inside tube using 14 mm (9/16 inch) socket, and slide nut part-way up mast.
  1. Raise antenna to run plastic drive wire at bottom of mast out of motor. Note direction of teeth on plastic drive wire.
  1. Saw off damaged portion of antenna mast. Remove burrs from mast and slide nut and contact tube off stationary tube.
Installation
  1. With the teeth on the plastic drive wire facing toward motor on antenna, push end of plastic drive wire of replacement mast assembly down into tube. Push it around curve at bottom of tube until end enters drive mechanism.
  1. Run motor down while pushing on plastic drive wire until about 305 mm (12 inch) of wire has been drawn into the tube. Stop motor and insert bottom of antenna mast into tube. Lower mast.
  1. Slide contact tube and radio antenna nut down antenna mast. Tighten nut to 0.45 Nm (4 lb-in).

  2. Raise and lower antenna several times to ensure proper operation.
651247a.gif

Jul 09, 2009 | 1995 Ford Thunderbird

2 Answers

Problem removing broken antenna mast


you have to pull out the trunk interior trim panels on the left side to access it.
there will a few 10mm bolts and a connector.

May 07, 2009 | 2006 Hyundai Sonata

2 Answers

Saab 9-3 convertable antenna will not go up. there is a clickng sound when the engine is turned off and on at the antenna.


antenna mast is no good.. you can buy a mast and have it installed or buy a used antenna and have it installed im sure Elite foreign auto parts has only saab parts.. tested and used,

Feb 17, 2009 | 2003 Saab 9-3

Not finding what you are looking for?
Panasonic CQ-C1100U CD Player Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Car Audio & Video Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Chris Gladden
Chris Gladden

Level 1 Expert

12 Answers

Are you a Panasonic Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...