Question about Ovens

4 Answers

Amana oven trying to clean oven. door lock keeps flashing and then it begins to beep with the work door flashing on digital sceen. then an f9 code appears flashing in that window iwth the oven beeping non stop ...

Posted by dmcb on

  • 1 more comment 
  • kingston12ha Dec 21, 2008

    tried all the solutions till have f9 problem

  • Anonymous Mar 26, 2009

    kay so i got the door open but it still continues to beep and flash f9 someone help

  • Anonymous Mar 17, 2014

    my oven wont stop beeping and giving error f9

×

Ad

4 Answers

eagle338

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,889 Answers

Error F-9 means:Door lock safety circuit on ERC sensed Replace the door latch assembly

To solve this...Just press and hold the door latch to unlock position and then press cancel for a few seconds. The latch will return to its original position

This will probably fix it..but if doesnt work try this
Try unplugging the oven from the electrical power. May release the lock, which is held in place by a tiny micro switch. If not and while the electric is still off or the oven is unplugged, use a bright light flashlight to look through the slot where the lock is in the oven, not in the door.

You may be able to use a thin blade screwdriver to move the lock to the release position. Check the angle of the lever. A slightly bent lever handle also can cause this type of condition.

If all else fails, remove the access panel on the front of the oven to access the locking device and release it. May have to disconnect the wires to the lock which will allow door to function but not during any self cleaning modes.

Posted on Oct 17, 2007

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

I DISCONNECTED OVEN FOR 10 MINUTES. PLUGGED IT IN AGAIN AND PRESSED CANCEL-CLEAN TOGETHER FOR 15 SECONDS. THAT SEEMED TO HAVE CLEARED THE PROBLEM.

Posted on Feb 09, 2010

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Kitchen Aid is a piece of "you know what", I had the same problem with the door locking on its own and not opening back up. The best solution without getting screwed by service tech is to start the self cleaning process, let the oven lock and then turn it off and it should unlock. Good luck!

Posted on Dec 24, 2010

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

All I needed to do was unscrew the 2 screws holding the lock assembly and it released it!! I screwed it back in and set the oven to self clean and it worked!!
Thanks for saving me the repair service call!!

Posted on Jan 28, 2008

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

GE monogram double oven . Self cleaning top oven and F9 in red showing and beeping noise


F9 is a problem with the oven door lock circuit. If the door is locked, it's probably a bad switch that tells the oven it's locked. If the door isn't locked, it's probably a problem with the lock mechanism.

A common problem on many built-in GE ovens (you don't say if yours is built-in or free standing...) is air circulation in the control panel. The fan that keeps the panel cool either stops working or gets clogged with dirt/dust and can't move any air. This causes the panel to overheat and can cause all kinds of odd problems and error codes. If you have a built-in, check to make sure the fan is working and the mesh screen behind it is clean.

Jul 17, 2016 | GE Monogram ZET3058SHSS Stainless Steel...

1 Answer

I push the bake button for the lower oven and it begins to beep and displays a F9 on the digital display


Hi

F9 is a door lock error and to solve this issue you can hold the light switch for 15 seconds, this will reset the control. If it won't work then hold the light switch in and set the unit to clean and after a minute press cancel to cancel the clean cycle. If still it won't work then the door lock assembly should be replaced. Hope this helps...please post back for further assistance.

Daniel

Aug 01, 2011 | Amana ACB6260A Electric Double Oven

1 Answer

Code f9 on frigidaire self cleaning oven. what does it mean. i went to clean the oven and the door locked and the code f9 came up and keeps beeping. i unplugged the stove for 1/2 hour and plugged it...


Hi

Thanks for using FixYa. F9 error in your oven/range indicates an issue with the door locks assembly and/or the door latch. To start with check the door lock circuit, you can also try to jump start it to see if it's working. If it's not working then the Electronic Range control has gone bad and should be replaced, if it is working then the door lock circuit should be replaced. Please do rate the solution if the issue is resolved or post a comment for further assistance.

Thanks
Rylee

Sep 15, 2010 | Frigidaire Ovens

1 Answer

F9 Flashing on Frigidaire 30" range


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE [email protected]#$

Dec 31, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Oven door locked.


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question!$%!!!%!%

Oct 26, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Pushed the clean button, the oven locked, and the screen started beeping and flashing f9 or f7. I hit cancel, and the oven is still locked and the clean button is sill flashing.... It has been 10 hrs!


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%^%$

Jun 21, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

My self cleaning oven door will not open, and keeps beeping and


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%$%^@#

Apr 19, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Stove door locked and continues to beep and flash code F9


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question$$%^^%$

Mar 27, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Door lock lites keeps flashing but the door is not locked


The F9 code indicates there is a problem with the door lock.

Try disconnecting the power to the range for 10 seconds and reconnecting. Open the oven door and hold the door switch plunger in while you try these things. Put the control into clean for 5 minutes then cancel clean. You must hold the door switch plunger in for the 5 minutes.

Try canceling the clean cycle without putting the control into clean.



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question^%[email protected]#$%

Mar 02, 2009 | Frigidaire 30" Self-Cleaning Freestanding...

4 Answers

F9 code


I hit the same F9 problem when trying to self-clean, except that the door was locked OPEN.

After much trial and error, I found the following fix: 1. Switch circuit breaker off. 2. Switch circuit breaker on. 3. Press Bake button. 4 Press the small/inside button which indicates that the oven door is closed.

The lock mechanism opened and the oven now works fine.

Nov 22, 2006 | Amana AOCS3040 Electric Single Oven

Not finding what you are looking for?
Ovens Logo

Related Topics:

1,366 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6181 Answers

Are you an Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...