Question about Washing Machines

1 Answer

Lg error code

Maytag top load washer

Posted by Karen Ragusa on

Ad

1 Answer

Ad

5 Related Answers

Anonymous

  • 706 Answers

SOURCE: Getting error code on lg front loader washer

Hello aj546,
Kinda figured there was a miscue there with your error code however... the error code FE refers to the fact that water is overflowing ( normally means the inlet water valve is stuck open and continues to let in water beyond the expected and/or sensed level.. so the water pump turns on to drain it and keep the level down. This kind of problem would probably warrant a aservice call from a tech since the majority of troubleshooting would require diagnosing the failed component itself and is not something that I recommend you try. There are too many pieces of hardware that have a direct impact on how this works and I highly doubt you want to play the shotgun approach..try this to see if it fixes the problem and if not..try that...
Before calling for service.. try this..
remove or disconect ac power from the washer..let it sit unplugged for at least an hour..then try washing 1 towel at the lowest cold water setting to see if that works ..if it does..repeat the process using only hot water.. if that works... then try the same test using warm water.. ( this test may help determine if the water inlet valve .,.either hot or cold is leaking through it)... If you still get the FE test..call for service.. That's the best I can offer via this chanel... BTW..if only one of the two tests fails.. ( Hot water only generates an FE error.. then chances are the hot water inlet solenoid valve assembly is either sticking open or the controls to that are commanding it to remain open... Hope that helped you..'
Regards,
Rick

Posted on Nov 29, 2008

Ad

Anonymous

  • 113 Answers

SOURCE: maytag neptune front loader washer has NF error code

Does it agitate and does the door lock light come on? Theres a panel on the back you can take off via 4 screws. Here you can check the belt and watch to see if it spins or moves at all. If the door lock light comes on, and you here the door click. Than chances are your motor control board is bad. Seen this many times. Im actually replacing one tomorrow on the exact washer.I believe the part # is 22004045. Heres a diagram. If the door doesnt lock than you need either a lock assy or a new computer for it. The computer is in the top panel where the timer is. If you look at it you should see a burnt resistor. If no burnt resistor than its more likely th lock assy. Ill try and find the part # for the lock and computer, and a digram. Hope this helps. Dave www.washermd.com

08f97d1.gif

Posted on Dec 19, 2008

Anonymous

  • 706 Answers

SOURCE: LG WM2277HW - ERROR CODE "LE"

Hello remrama,
Please use this link to access the service manual on your display code message ( page 18 ) elaborates on the cause of that message. You should be able to determine which of the few causes may be the culpret,... http://136.166.4.200/contents/Laundry/WM2277/WM2277xx_Service_Manual.pdf

Hope this helps you..
Regards,
Rick

Posted on Feb 22, 2009

sivaranjini

Sivaranjini

  • 241 Answers

SOURCE: Maytag Epic giving F11 error code!

ths.gardenweb.com/forums/load/.../msg1012004912002.html

Posted on Jun 22, 2009

Anonymous

  • 3 Answers

SOURCE: maytag bravos top load washer error code F1

Well, you're not gonna like this, but here's the deal.

Remove the three screws on the rear of the control panel and lift it up. Disconnect the rubber hose on the right side of the gray control module and blow through it to make sure it is clear and not kinked. If this check is fine then your control module needs replaced.

Note that Maytag knows this is a fairly common problem. My washer failed 9 months out of warranty with this problem.

The only good news is that it is an easy, though expensive, replacement.

Posted on Sep 25, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Specs for model#MVWC400XW0 Maytag Centennial Washer


It definitely could be a clogged or bad pump. However, it's always a good idea to check for error codes before replacing a part...Especially expensive ones...
http://applianceassistant.com/Washer-Repair/Maytag-Centennial/Maytag-Centennial-Washer-Error-Fault-Codes.php
Hope it helps! Good luck!

Mar 02, 2015 | Maytag Centennial 3.2 cu. ft. SuperSize...

1 Answer

I have the maytag series 4000 and got the f2 code. I have cleaned the.hoses and wven replaced the drain pump. Is thete a rest button? It is still not working and.shows the same code


F2 code is water level to high

Washer Error Codes
Below is a list of washer error codes for HE & conventional top load washers and front load washers. As more error codes are found or published, we will add to the list. Right now you will find error codes for Asko, Fisher & Paykel, Frigidaire, GE, Kenmore, LG, Maytag, Samsung, and Whirlpool. This list might not be complete and should be used for reference only.
Asko Washer Error Codes
• F1--Water supply/low water fill.
o 1. Check water supply to machine.
o 2. Replace water inlet valve.
• F2--Water level too high.
o 1. Plugged/Bad water pump.
o 2. Faulty water valve.

Sep 19, 2014 | Washing Machines

1 Answer

My lg washing mechine error code EP


Write your answer...my lg top load washer displayed EP or E2 error codes and washer is not working

Jan 30, 2014 | LG WFT1071TP Top Load Washer

2 Answers

Lg top load washer e6


E6 is listed by Samsung as :- Water temperature rising/falling too quickly. Check thermistor.

Oct 21, 2012 | LG WFT1071TP Top Load Washer

1 Answer

Maytag top load washer op error code, washer wont start. Checked and magnet is in place, what else can it be?


If you place a couple magnets over the left gray bumper and the "OP" error code doesn't clear then I feel you have a problem with the Left Hand Lid Lock.


See if this post will help; Left Hand Lid Lock Troubleshooting

Sep 29, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

My Maytoag Bravos Top load washer drains really


Is the drain hose kinked or clogged? Is the drain hose installed properly? look in the installation Instructions, Press POWER/CANCEL to clear display........ hope this helps.....

Jul 09, 2009 | Maytag Bravos MTW6600T Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18455 Answers

Cindy Wells

Level 3 Expert

6182 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...