Question about Maxent MX-27X1 27 in. HD-Ready LCD Television

2 Answers

Blue screen, no picture, but sound

2 yr old ,27inch maxent.......there is sound but the picture is all blue......help..live in canada, niagara falls..........do l need to repair it here or take it back to floridia where l purchased it

Posted by annaglenn on

  • skysharkey Mar 11, 2009

    as soon as i turn the tv on, i get scrambled lines all over the screen, they are normally vertival, then it seems that the tv tries to get a screen and then just turn blue, i do have sound though

  • skysharkey May 11, 2010

    yes sir, i have tried all inputs even the pc, for a while i had some scrambled version of a screen on the pc but it soon turned to complete vertical lines, turning the tv on and of didnt reset this

×

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Have maxent 26 lcd no sound no picture but blue screen
what would cause this it also get lines across the screen

Posted on Sep 04, 2011

Ad

Jay Henderson

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 261 Answers

Does this happen on All inputs? Let me know. Thank you Jay.

Posted on Feb 02, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Troubleshooting for maxent mx-42hpt51


hello!
Blue screen(bright blue) indicates an absence of signal. If you have "on screen" display characters: menu, channel ##, volume bar, etc, your set might be configured for digital antenna settings, or DTV, "air" mode. Then, you won't be able to get cable channels through. If your "blue screen" is dim and there is no any characters, then your Y-sustain module is bad. Especially, if you have encountered loud "pop" shortly before "blue screen" appeared. Then, it's a major repair with board(s?) replacement. If you can handle that, get back to me in a next session. I will guide yourself "how to".
Thanks,
Alex.

Feb 16, 2012 | Maxent MX-42HPT51 42 in. Plasma TV

1 Answer

I have a 42" Maxent plasma TV about 7 years old.


Is it 7 years old? Marvelous. Exciting. the lifetime of Maxent televisions are 6 moths the most!!!
You're lucky.

May 12, 2017 | Maxent MX-42VM10 42 in. HD-Ready Plasma...

2 Answers

Hi, Maxent P420142x3. Screen picture has gone....


my maxent p420142x3 i have sound but no picture any answers

May 19, 2010 | Maxent MX-42HPM20 42 in. Plasma HDTV

1 Answer

My 27inch westinghouse flat screen has sound but


Ur LCD inverter board is dead.Replaced this LCD inverter board u will get ur picture back.This a simple repair take ur tv aparts,take out the LCD inverter board,it a long shape of a board.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish LCD inverter board for the replament.U will get ur picture back.Ok,good luck,labors about an hour work.

May 08, 2010 | Westinghouse 26" LCD Flat-Panel HDTV

1 Answer

Blue, green, red parallel curved lines at top of screen


hello sorry but it sounds like the chip have gone again when you replace these chips you might have to change the resistors and the 2 capacitors as well

shaun

May 08, 2009 | Mitsubishi WS-55905 55" Rear Projection...

1 Answer

Picture problem with Maxent Plasma MX-42HPM20


Very common problem on these sets caused by bad surface mount caps. Check on ebay for a repair kit it's the only place I know where one exists.

Feb 23, 2009 | Maxent MX-42HPM20 42 in. Plasma HDTV

2 Answers

Hooking up a Mac to tv


I ran into the same problem with my "50 maxent. The manual clearly states that mac resolutions are not supported. We won't let that stop us. Step one is to download switchresx. It's a simple utility that should allow you to define custom resolutions. http://www.madrau.com/ .
Step 2 is to download chicken of the VNC. http://www.macupdate.com/info.php/id/9517 . Once this is installed on a separate mac from the one you are trying to connect to the maxent take your mini and hook it up to the RGB port on the maxent and boot it up. Once this is done use chicken of the vnc to take control of of the mini with the other mac. Now you can change the resolution on the mini using switchresx which you installed on the mini earlier. In the case of the maxent you will need to set it to 1366x768 at 60 hz. If using another flat panel consult your user manual for the correct resolution. In my opinion there is no flat paned tv this should not work for.
Good luck!

Sep 30, 2008 | Maxent MX-42HPM20 42 in. Plasma HDTV

1 Answer

No picture, just a blue screen and sound


a hard reboot fixed the problem...it was a cable issue

Apr 04, 2008 | Panasonic VIERA TH-65PV500 65 in. Plasma...

2 Answers

Hitachi 50" plasma no picture


how do i fix p50h401 blue light no picture and sound

Feb 07, 2008 | Hitachi P50H401 50 in. Plasma HDTV

Not finding what you are looking for?
Maxent MX-27X1 27 in. HD-Ready LCD Television Logo

Related Topics:

597 views

Ask a Question

Usually answered in minutes!

Top Maxent Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76587 Answers

Cindy Wells

Level 3 Expert

6262 Answers

Paul Bade

Level 3 Expert

1688 Answers

Are you a Maxent Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...