Samsung le40b530 When I turn on the TV, audio is 0 and the volume indicator on the left is fixed and can't use any other command from remote. If I push the volume button on the side of TV, the volume rise up, but as I release the button volume get down automatically to 0. What could it be ?

Using the volume control buttons on the television itself (not the remote) turn the volume all the way down to 0.
Using the volume controls on the Digital box itself.
Turn up the volume until it is at the maximum.
Using the television's volume controls again; raise the volume to a comfortable level.
If you are still experiencing the audio problems on this television, it is possible there is a loose connection on the television.

If volume bar is presented continuously, the TV is in a continuous command volume down state. Could be volume down button down stuck on TV, or possibly remote, or some other device capable of emulating a remote is issuing command volume down. Or control logic in TV has failed with this unusual result.

Press the MODE button to make the TV
indicator on the remote control flash.
2 Press POWER button to turn on the TV.
3 Point the remote control toward the TV.
4 While holding down POWER, enter the code
corresponding to your brand of TV.
• If the code matches the TV's code, the TV will be turned off.
• If there is more than one code listed for your TV in the table,
enter one at a time to determine which code works.
Example: For a Samsung TV
While holding down POWER, use the number buttons to enter 00,
01, 02, 03, 04, and 05.
• You can use the POWER, TV/VIDEO, VOLUME, CHANNEL, and
Numeric buttons (0~9).
5 Pont the remote control toward the TV and press
POWER. If the TV turns off or on, the setting is
complete.

Hello;

Without knowing the codes for the specific brand names and models of your devices, this is how you program the Zenith MBR3447 for your TV, VCR, DVD Player, CD Player or Audio Receiver:

TV

1. Push the "Power" button on the TV to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "TV" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the TV's IR sensor and push the "Power" button. Pause a second. If the TV fails to shut off, push the "Power" button again. Repeat until the TV does shut off. Each time the "Power" button is pressed the Zenith MBR3447 tries using a different TV device code from its code library to turn the TV off. Therefore, when the TV finally does shut off it's an indication that the remote is temporarily programmed with the correct device code to control the brand of TV you're using.
6. Press "Enter" to save the current code.

VCR

1. Push the "Power" button on the VCR to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "VCR" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the VCR's IR sensor and push the "Power" button. Pause a second. If the VCR fails to shut off, push the "Power" button again. Repeat until the VCR does shut off. Then press "Enter."

DVD Player, CD Player or Audio Receiver

1. Push the "Power" button on the device your programming the remote to control to manually turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "AUX" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the device's IR sensor and push the "Power" button. Pause a second. If the device fails to shut off, push the "Power" button again. Repeat until the device does shut off. Then press "Enter."

If the volume indicator appears and respond as you increase the volume but the sound does not respond, there might be a problem on the audio section.Ask for a repairman to check it. If the indicator does not respond, try using manual control instead of using remote control.Also some units have features to turn speaker off or on. Go to menu scan for audio check if it is turned off or on.

Try to check the pannel and the remote "volume down" buttons - one of them could be stuck in a pressed position.

It usually happens on the remote when dirt or sticky substances accumulate around the rubber buttons - you need to disassemble the remote and clean the rubber pad and the remote housing with some ethyl alcohol and cottonwool, also clean well the holes on the housing where the buttons protrude.

If you also decide to clean the contact tabs on the rubber pad and the circuit board, you should clean them gently to avoid damaging the conductive coating.

I hope this helps somewhat.

regards

3rq8 (Triarcuate)

smith,

good day, not so familiar with this model but try this.

1) try to check in your DVD remote controller if it does have a + and - buttons indicating volume , if does have this features press + button to increase the sound output

2) if remote commander doesn't have this features try accessing the " SETUP" menu. most probably there would be a button in your dvd remote indicating this button "SETUP"

3)once you've access the setup menu, there would be a dialogue box indicating ( Video setup, Audio Setup, display setup, parental lock) insome cases it will show you a display picture of all this menu

navigate the dialogue box and look for "audio setup" once you've access this part there would be options and controls where you can change the volume/audio settings .


cheers,
mark

yo moel
the way i did it was take the batteries out and hold powere button for 5 seconds put batteries back in and should be fine mate!

ahmed

Need to get more granular on this, Does the volume work HT remote, for like radio, cd, ipod audio? For you to use the tv audio through the HTB the tv's audio settings should be on the "fixed" output option. This gives a line level to the Amp independant of the tvs volume adhjustment. Otherwise you will need to adjust tvs volume 75% or so before the audio amp will reproduce a good volume. Turn down audio amp prior to making any adjustments. Let me know thx

There could be a cable that is not completely seated inside the set, there may be a software upgrade also that will fix it.