Change name of 1 extn

Extn. phone may be defective or check up the wiring going to Extn.for damage.or replace the wiring.

Press PROGRAM press BUTTON press (0 to set a line button, press 1 to set an extension, press 2 for a outside number) Enter the number (line number or extension number or 9 followed by outside number) Press STORE

The handset has been programmed to auto answer all or some calls. You will need to change it to normal answer mode via EXTN 20/21 whichever is your programming extension. To tell which one is your default extension it is usually the extension that will still work as a normal telephone in the event of a mains power failure.

Nope. You can log the phone in as any extension.

r u using CTX/CIT system??
this only apply for CTX/CIX
to set extn ket at flexible button
press  #9876
press  HOLD
press the flexible button u wanted to assign
press 610 follow by extn number
press again the plexible button to confirm
repeat step for other flexible button

to set name must go to administrate phone
press MODE at the display
press ADMIN
key in password
default password are ' 0000 '
press HOLD, display will show phone name
press HOLD, again will show DN ID
DN stand for extn
key in extn number then key in name
HOLD again to confirm setting
repeat step for other name

Ok, well I can explain most of the programming template, but I cannot give you the exact buttons to push since each phone IS programmed differently.

-> first dial FEATURE 985 this will give you the DN(Extn) for the voicemail (record this number) and then RLS
-> now I need you to dial FEATURE 0 on your set, and press the Intercom key to ensure the extension of your set you want to change and then hit RLS.

To get into programming press FEATURE 2 6 6 3 4 4
-> Password: 2 6 6 3 4 4
Now you will see 3 arrows on your LCD
<- Heading Enter->
<- Back Next->

-> you will now see TERMINALS&SETS and press Enter (the top right arrow key) now put in the extn that you want to change.
-> you should now see the extension of the set and the name that is associated with it, press Enter (the top right arrow key) again
-> now you will see LINE ACCESS and press Next (the bottom right arrow)
-> then you will see CAPABILITIES and press Enter. now you will see FWD NO ANSWER and press Enter, and put in the DN of the voicemail you saw with the Feature 985
-> hit Next for the number of rings you want to ring at the set before going to voicemail.
-> hit next and you can now RLS to back out of programming.

Voila, that set once called will now goto voicemail.

-OR-

You can get the receptionist to dial FEATURE 9 8 6 and the extension to transfer directly to someone's voicemail.

go to administrator phone
usually are receptionis phone
press MODE button
press ADMIN
key in pasword "0000"
display show phone name
press HOLD to skip
display show DN ID
DN stand for extn number
key in extn number
the exiting name will shown...use scrool n page for backward n forward the cursor
key in the person name
press hold to confirm
to exit press MODE button untill time n date r displayed

Sounds like the station is in do not disturb mode.Internal, external and transfered calls do not ring but the station can still make calls. there should be a lit button on the set maybe marked do not disturb or DND. press the button again to turn the led off. hope that helps

press intercom #9876 HOLD, flexible buttoon pressed to assign, press the bitton code, press again the bitton to set DND = 180 short key for extn 610+extn number to change display name must set at administrator phone usually is receptionist phhone

1. Press feature
2. Type **266344
3. On password type 266344 (wont show the numbers as you putting them in)
4. Terminal + extns will appear, press line 6
5. Find ext number, type number and the name will show up
6. Press line 6, line access will appear
7. Press line 7 twice and change will appear
8. Enter the name then press line 1

End session and save

worked for me, hope it helps