Question about Whirlpool Duet Steam WFW95HEXW

1 Answer

Error code F06 and E01 - Whirlpool Duet Steam WFW95HEXW

Posted by Jana Castillo on

Ad

1 Answer

mindlessforu

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 7 Answers

Here is what the F06 code stands for
Drive Motor Tachometer Error
The control is unable to properly detect motor speed and the machine will shut down.
If a failure occurs during high-speed spin the door will be unlocked after 3 minutes.
Potential Causes
• Check wire harness connections between the Drive Motor/Tachometer and the
Motor ControlUnit (MCU), and between the MCU and the Central Control Unit
(CCU)
• Check the Drive Motor
• Check the MCU
• Check the Wire Harness

Posted on Dec 14, 2013

Ad

2 Related Answers

shaun taylor

  • 1527 Answers

SOURCE: error code f06

hello fo6 means drive motor techometer error check wire harness connections between the drive good luck




shaun

Posted on Mar 22, 2009

Ad
ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: i get an f06 and

F6 code is an issue with the motor drive tachometer.

Most often this is caused by poor connections at the machine control or motor controller. Locate the main machine control by removing the top panel and the motor control by removing the rear panel. Remove each connector, one at time, and reinstall. If this does not work, you likely have a faulty control.


E1 means that the thermistor is open and needs to be replaced. The connections can be loose but the most likely cause of an E1 error is a bad thermistor.

If you're comfortable and confident in your do-it-yourself skills and have access to a volt/ohm meter you can check and replace this part yourself.

For replacement parts - head on over to SearsPartsDirect.com - PartSelect.com - or RepairClinic.com and enter in your full model number for a full parts listing.


Hope helps.

Posted on May 28, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

What is causing error codes F06 E01?

This error message means an electronic communications problem. Press pause/cancel twice to cancel the error and then disconnect the power cord from the outlet, wait few minutes, plug the power cord back in and select a new wash cycle.

If you see the same error again then you need to check the connections located between the drive motor and motor control unit.
0helpful
1answer

E01 F06 Error messages during normal wash. What do they mean?

You'll need to look on your tech. data sheet that came with your machine and do the TESTS it tells you to do. Its located in the bottom of the washer on the inside cabinet panel.
0helpful
2answers
0helpful
1answer

My whirlpool duet washer has error codes, F06, E01 and int. how can I reset the washer?

The Electrically Erasable Programmable Read-Only Memory (EEPROM) on the main electronic control board is corrupted. Unplug the washer for 5 minutes, restore power and see if the code clears. If not, the replace the main electronic control board.
0helpful
1answer

Model MHW6000XG0. What do E01 and F06 error codes indicate?

Communication error between the CCU (Central Control Unit) and the MCU (Motor Control Unit).
0helpful
1answer

Maytag Maxima front load washer "master reset"?

To start, E01 and F06 means that your main central control board (CCU) and the motor control board (MCU) are not communicating with one another properly. The motor control board is located under the tub mounted to the floor of the washer. The CCU is mounted under the top panel of the washer and is the part with about 100 wires going into it. You'll want to remove the top panel and the lower front panel to check the wire connections and make sure they are all secure. If everything looks good, then you just have to somewhat guess which control board you want to replace first, either the MCU or the CCU. The problem is that there is no way to test and determine which part is faulty so it's just a guessing game. That's what makes this one of the worst errors to get. I generally replace the CCU first as that is the part that shakes around a lot more during spin and it's the first place that the power goes from the power cord if there is any fluctuation in power, so it makes since that this part fails more than the mcu.
There is no Master reset. The only thing you can do is unplug for 1 minute then plug back in.

I’m happy to help further over the phone at https://www.6ya.com/expert/george_083af2f0afc0328b

0helpful
1answer

How can i fix error 0001

Xbox-experts.com - Error code 3 RLOD E01 / 0001

https://xbox-experts.com/errorcode/E01/0001/
General info on Error code : 3 Red Lights E01 0001 and how to fix it!. Short circuit in the console/faulty PSU. E-Code / Secondary Error code‎: ‎E01 (No ...
Binary/Hex‎: ‎00000001 / 0x01 -> 1
Primary Error code‎: ‎3 RLOD
0helpful
1answer

I have a whirlpool duet steam and reads codes F06 E 02 and replaced the electric controller and now reads F06 E01

OK your almost there. The switch or Latch that locks the door is faulty or bad. It is either that or probably not connected to the right terminal. New control board!!! That was expensive! Good luck!

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_b77d19396bfe2249

Not finding what you are looking for?
Whirlpool Duet Steam WFW95HEXW Logo

2,687 views

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...