Question about Heating & Cooling

1 Answer

The air conditioner wasn't on and the control box was displaying a U9 error

What is the problem when mr slim displays a u9 error.

Posted by jknapp178 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

U9 error code means there was a problem with voltage to the unit.Can be caused be either overage or a shortage. Have you had any power outages?

Posted on May 15, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Preset heat stuck at 63. I want to lower the temperature for a vacation


[PDF]PAR-30MAA - Mitsubishi Electric Australia

https://www.mitsubishielectric.com.au/.../IB_PAR-30...

Mitsubishi Electricand Mitsubishi Mr. Slim Air Conditioners. MA Remote Controller ..... Heat. 17 ~ 28 ?C (63 ~ 83 ?F). Auto. 19 ~ 28 ?C (67 ~ 83 ?F). Fan/Ventilation. Not settable. 13 ...

[PDF]PAR-31MAA - Mitsubishi Electric Australia

www.mitsubishielectric.com.au/.../par-31maa_ib_en.p...

Mitsubishi Electricand Mitsubishi Mr. Slim Air Conditioners. MA Remote ..... Heat. 17 ~ 28 ?C (63 ~ 83 ?F) .... Preset cooling temperature is higher than preset heating temperature.

My air recycle button just blinks. Also when i turn on the - Fixya

www.fixya.com/support/t26081705-air_recycle_button_just_blinks_also
6 hours ago - Not sure the heat pump is producing enough heat. Nov 04 ... Preset heat stuck at 63. ... Feb 05, 2016 ' Mitsubishi Electric Mr Slim E12C26426.

[PDF]MA Remote Controller Mitsubishi Electric PAR-21MAA ...

planetaklimata.com.ua/.../Mitsubishi_Electric/Mitsubishi_Electric_PAR-2...
Easy Maintenance Function (Only for Mr. SLIM PUHZ series) . .... 4.4.3 Automatic Cooling/Heating Display Setting . ... Monitoring the Operation Data by the remote Controller (for Mr. SLIM) .......... ..............48 . How to .... 63. 4.2 How to set rotation function(back-up function, 2nd stage cut-in function) . ... Preset temperature (. °C. ).

Feb 05, 2016 | Mitsubishi Electric Mr Slim E12C26426...

1 Answer

Daikin air conditioner flashing fault code u9


U9 System communication failed Fault with other indoor unit, ie no power, Faulty PCB

Aug 10, 2012 | Heating & Cooling

1 Answer

Eo error code indoor unit runs 2-3 seconds then gives eo error code problem started when mr chipmunk chewed mr slims 12 volt wire connecting to out door unit and shorted it . Outdoor unit has bad control...


You need a professional here. Once this has been repaired, I would suggest running the wiring to the outdoor unit inside some sort of piping to protect it.

Jul 20, 2010 | Mitsubishi Mr. Slim MXZ30TN Air...

1 Answer

Code u9-80


This indicates a communication failure between the Main Control Unit and the operation control circuit board. Power the machine down and disconnect from hte power supply. Check all the connectors and wiring on the boards and also any loose wiring that may be grounding the machine. Power back up and if the fault persists a qualified copier engineer will be required.

Mar 10, 2010 | Sharp AR-M237 Copier

1 Answer

Mr Slim split system with no display on remote control or unit display.


Mitsubishi Mr slim comes with no diplay on the indoor unit but there is small display on th eremote unit.for further help kindly send your air conditones complete model

Jul 09, 2009 | Heating & Cooling

1 Answer

I have a Moto U9 and have problems with the display freezing


you may need to take the batery out and give it a blow then put it back in and try again

Feb 11, 2009 | Motorola Mobility MOTO U9 Pink Cellular...

1 Answer

WORKCENTRE PRO 420 U9 CODE


Hello sir; The U-9 code means the main control unit/switch board problem, replace it.

Feb 07, 2009 | Xerox WorkCentre Pro 423 Copier

1 Answer

Rank xerox 5328 U9


if its a u9-1 code it is the lamp that is faulty. Sometimes it can be the connections either end of the lamp but normally the lamp itself. It will probably cost as much to fix as it would to get a new one to be honest

Nov 03, 2008 | Xerox 5830 Copier

1 Answer

Xerox 5328 copier error


U9-3
Xerographic process problem.

The Exposure sensor detected low Exposure Lamp intensity. Switch the Main Power Switch off then on in order to clear the Status Code. Go to the U9-3 Xerographic Process Problem RAP

U9-4
Xerographic process problem.

The Main PWB sensed that the Toner Dispense Motor was not running. Perform 20-3 U Codes Clearance . Go to the U9-4 Xerographic Process Problem RAP

U9-5
Xerographic process problem.

The CSDC zero point was too high during auto setup. Perform 20-3 U Codes Clearance . Go to the U9-4 Xerographic Process Problem RAP U9-5 Xerographic Process Problem RAP .

Aug 09, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

755 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts

Paul Carew

Level 3 Expert

3522 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18455 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...