Child lock Can not start - picture of lock

The child lock is a lever alongside the door lock on the rear doors.

Hi there
Some are different ways. but you can try this.
If you want to activate the child lock function hold down the Temp. and Spin or Rinse buttons at the same time for 3 seconds. Click here to view a simulator showing you how to use the Child Lock. When the child lock is activated only the power button works.
========================================== or

1. 1 However, Child Lock does not activate until you press Start/Pause.
   
2. 2 Child Lock does not activate until you press Start/Pause. In the holding state, you can open the door or change settings by pressing corresponding buttons. However, once you press Start/Pause to start the washing machine, the Child Lock will be reactivated.
   Can only try
   All the best Clive

Setting child lock
The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally changed. The child lock function locks all buttons and the programme knob. The child lock can be activated or deactivated by holding down the OPTION and OK buttons simultaneously for 5 seconds.

• Before programme is started: Appliance cannot be used
• After programme is started: Programme in operation cannot be changed

The icon appears in the display to indicate that the child safety device is activated. The child safety device is not deactivated once the programme comes to an end. If you want to set a new programme, you must first deactivate the child safety device.

Dado

Below is Child Lock Icon

On the Audi Q7, depending on country and options the child lock is either:

1. On the drivers armrest, near the window switches, there are 2 buttons with a little orange light and a picture of a little baby on them. Deselect both buttons to turn off the child locks.
-OR-
2. Open the passenger doors, there is a small keyhole on the inside of the door above the latch, use your key and turn it 90 degrees to turn off the child lock.

Hope that helps

Child Lock is activated. Look for a picture of a small child's face on the Facial Panel (usually with picture of a lock) follow the arrows to 2 buttons, press and hold these buttons for 5 - 7 seconds. Child Lock will then deactivate.

Hope this helps

* If you found this solution helpful, please vote positively.

Hi there,

You can use the child lock feature in 2 ways.

1. To prevent operation of the washing machine when no wash cycle is running

To set this feature, switch the machine on using the POWER button at the top-left of the control-panel. Next, press and hold both the SPIN and RINSE buttons for about 3 seconds - until the child lock light indicator on the control panel illuminates. All functions of the washing machine will now be disabled apart from POWER ON/OFF until such time as the child lock is deactivated.

To deactivate the child lock, press and hold the SPIN and RINSE buttons again until the child lock light indicator on the control panel goes out.

2. To prevent any tiny fingers from tampering with the machine while a program is running.

After pressing the START/PAUSE button to start the wash cycle, press and hold the SPIN and RINSE buttons until the child lock light indicator illuminates. All buttons on the control panel will now be disabled until the child lock has been disabled. When the wash cycle has finished, you will need to switch the child lock off again to reactivate the buttons. Once you have finished using the washer, reactivate the child lock again before switching the power off as above.

The feature can also be used when using the delayed start feature, but needs to be set after pressing the START/PAUSE button.

Hope this helps. Please let me know if I can be of further assistance.

Regards,
BElectric

Hi.

Samsung machines error codes are numbers and letters, then I the machine is not in fault mode, but child lock has likely kicked in.

Here is child lock icon:


Try the following:

ACTIVATING/DEACTIVATING
If you want to activate/deactivate the Child Lock function, press the Soil Level and Signal
buttons at the same time for 3 seconds.
How It Works:
1. "Child Lock" can be activated while your Washer is running.
2. Once you activate "Child Lock", all controls (except for the Power button) will be locked
until you deactivate "Child Lock".
3. The Child Lock button will be lit while it is in effect.


Here the user manual.

look at the control panel there is a button that has a picture of a lock or a child by it, that is your child lock button, hold button down until lock light goes off

Show me how to take the safety child lock off switch also I need a picture of this location on the door

On my NN-L738BA there is a Child Lock feature.
You set the child lock by pressing the Start button 3 times.
If the Child Lock is enabled it displays the word :CHILD".

To disable this feature on my microwave the manual says to
press the Stop/Reset 3 times.

Check your manual for the Child Lock.