Question about Audio Players & Recorders

1 Answer

''V-PROT'' ERROR MESSAGE ON DENON D-M37DAB MICRO SYSTEM.

As soon as unit is switched on clicks....get ''PLEASE WAIT''....clicks.... use remote control and get V-PROT followed by cut off.

Posted by lawlor111 on

Ad

1 Answer

Francisco Mauricio G

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,550 Answers

The audio amplifier IC´s are burn out

Posted on May 05, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

. Can I buy a switch unit that plugs in where the unit for remote is and has chain pulls and light ?


I am not sure we can follow. Please set some context like

Remote of what equipment ? TV / Heater / DVD / STB / Lights ?
Perhaps you can reword your question for us to contribute

May 29, 2016 | Televison & Video

1 Answer

Sony bravia kdl-40w600b..turns off after switching on..and the red light indicates 8 time..whats the issue..and need to resolve


8 red flashes- main board sp prot, try power reset, update with usb, or replace main logic board


How to service fix phones tablets PCs TVs and tech reviews blog by Tampatec

Factory reset:

https://us.en.kb.sony.com/app/answers/detail/a_id/43126/c/65,66/kw/factory%20reset/session/L3RpbWUvM...

First I unplugged my HDMI cable and powered OFF my router (using wireless).
As soon as HDMI 1 showed on screen, pressed the arrow up button on remote, touched the power button on left rear side (uppermost) button on my TV) and let go of arrow up. TV said RESET and after a min, TV went back to setup screen. Followed Setup onscreen instructions and working OK.

May 11, 2016 | Sony Televison & Video

1 Answer

Why does display says"please wait". message on screen reads "searching for software. no respose to controls.


under somewhere there is a reset button push for 5 - 10 secs and go from there.

Aug 28, 2014 | Televison & Video

1 Answer

How to hard reset unit without remote


  • Reset the unit to factory default settings as follows:
  1. Press [POWER] on the unit to turn off the unit.
  2. Press and hold [FAST FORWARD] and press [POWER] and [OPEN/CLOSE] on the unit at the same time for more than 5 seconds until "PLEASE WAIT" is displayed on the unit.
  3. The power is turned on and then turned off automatically.


http://service.us.panasonic.com/OPERMANPDF/SCBT200.PDF

fe998989-c1c6-42fd-a03f-a1a138fc88cc.png

Feb 18, 2014 | Panasonic Audio Players & Recorders

1 Answer

Casablanca Isatope 52 inch fan not working


You are exactly correct...

Power flows to the fan as soon as the circuit is closed.

All the light (diming) and motor power, speed & reverse are all
controlled by tones from the switch to a receiver inside the fan housing... (only 2 wires + ground).

I have BOTH (the old style 3 switch) and the newer 4 button "W32" ... use the same tones BUT ARE NOT INTERCHANGEABLE...

In my opinion
The premier site for ALL FAN switch troubles
is the "FAN-MAN" (see below).

Or call... 1-952-898-2754

Fan Man Lighting

Carnac the Magnificent

Apr 02, 2017 | Casablanca Fan Televison & Video

1 Answer

Our Infinity RX26 is cutting out soon after the hot water tap is turned on, we get a few seconds of hot water then nothing. We are cold! please help!


sounds like faulty thermostat controller disconect from hw unit and try the water again if it stays on the controller is faulty if you dont mind not having controll over the temp of the water you dont need a controller to opperate the hws

Jun 10, 2011 | Rinnai Digital Remote Water Heater Control...

3 Answers

HT-Z320 displays PROT code and then shuts down


i had the same problem a prot display then it would shut down. turns out i had the sub disconnected(noise complaint from the shaking at my apartment complex) but the speaker wires for the sub connected to the amp or central unit. when i disconnected the sub i left the wires on the floor behind the sub separating the pos. and neg. somehow the wires got moved around and the pos was touching the neg. as soon as i noticed and fixed this problem the system was working fine. my samsung hometheater model is HT-BD1250

Dec 29, 2009 | Samsung HT-DB120 System

1 Answer

I have a 2004 tacoma. Remote starter doesn't work. Dash lights on right side of the dash are dim. Remote starter was pro installed 4 years ago. Any ideas? Thanks


look under dash for the unit, remove the 2 fuses in red jackets wait 2 minute then replace fuses

if you have a 4 BUTTON REMOTE CONTROL:
You will need to take the unit out of safety mode, to do this you will
need to ground the hood pin switch wire, then put your foot on the brake,
next hit any button on the remote and the clicking will stop. Then you will
need to take the hood pin switch wire off of ground and take your foot off
of the brake and see if the remote will work with the unit

if you have a 2 BUTTON REMOTE CONTROL:
You will need to take the unit out of safety mode, to do this you will
need to put your foot on the brake, next hit any button on the remote and
the clicking will stop. Then you will need to take your foot off of the
brake and see if the remote will work with the unit

Dec 15, 2009 | Bulldog Remote Starter & T-Harness Kit for...

Not finding what you are looking for?

Open Questions:

Audio Players & Recorders Logo

Related Topics:

1,847 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

 Grubhead
Grubhead

Level 3 Expert

5700 Answers

The Knight
The Knight

Level 3 Expert

76466 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...