Belkin N router and linksys ip cam

Both the routers are having the same default IP addresses that's why they are conflicting.
Put only one router in the switch connected the a PC on the same LAN.
Open your browser and put the default IP address (like for most of the routers 192.168.1.1 or 192.168.0.1), hit enter and give the login ID and password (in most of the cases, admin/password orv admin/admin), go t configuration> IP settings> Static IP Mode> Change the IP from 192.168.x.1 to 192.168.x.2 (or any other other number except 1 and <254).
Save and reboot.
Now enjoy both routers plugged in simultaneously in the same LAN. :)

The printer's IP address most likely needs to be changed.
Check the Belkin's IP address range (it maybe 192.168.2.***) and configure the printer's IP address accordingly.

connect your computer to netgear modem alone and check for the ip address in the computer
(make sure that you have selected "assign ip automatically" in computer)...
to open command prompt type "cmd" and hit enter in run box...
then you can check ip address by typing "ipconfig" in command prompt...
make a note of IP adress or ipV4 address found under the heading "ethernet adapter local area connection"
it might be 192.168.X.X
now connect only the belkinrouter and check for the ip address using the same steps above...
it might be 192.168.2.X
make a note of that...
now compare both the ip addresses if they both have the same value in first three places...that is
192.168.2.... or something like 192.168.1.... or 192.168.0.... then you are facing with double NAT issue...
all that you need to do for that is to change the ip address of belkin router...
if it is 192.168.2.1 change into something like 192.168.15.1...the issue will get resolved....if not you can reset the belkin
router by pressing and holding the reset button for 30 seconds using a toothpick when the power is turned on...

1. Please check your computer's IP address should be autamatic.

2. Please do not connect your cable from your computer to Belkin's Internet port

3. Please connect your cable between your computer to belkin router's 1,2,3 or 4 number's port

4. Please check you cable should be not cross cable.

You probably need some service technician's guidance for closing this issue.

First of all, plug in the router as you always did to the old computer. Follow the steps below
Click on Start --> Run . type cmd in the command prompt, type ipconfig. Make sure the ipaddress you see is in the 192.168.... series. If you dont see the 192.168 series IP address, make sure you dont have a static IP.
Thanks
Ranjit

1. How do you connect your Linksys router to Belkin router? Do you connect your Linksys router to the Internet/WAN port of the Belkin?
2. If so, what is the Internet connection type set in your Belkin router? Is it dynamic?
3. If the Belkin router is set to dynamic IP and if it is obtaining an IP address from your Linksys router(you may check the status page of your Belkin router and look for IP address), then you may need to forward or set that IP address as the DMZ to your Linksys router. Make sure that XBOX is still configured as the DMZ host in your Belkin

Hope this helps!

Hi,
The first thing I would do is check to make sure the desktop with XP has the network card set to "obtain an IP address automatically"

if it is set to obtain an ip address automatically, I need to know the following:

What is the IP addresss of the router?
What is the IP address of the Vista computer?
What is the IP address of the xp computer?

You can find the ip address by going to start, then run, then type cmd and hit enter. at a command prompt type: ipconfig and hit enter.

Belkin says IPSec pass thru works now. I'll know tomorrow.

http://www.belkin.com/contact/milan/default1.aspx?id=580959590B0A5E0C0B5A59575B595F0A305F5D

F5D8231-4 WW v4.00.18

http://www.belkin.com/contact/milan/filedownload.aspx?id=580959590B0A5E0C0B5A59575B595F0A305F5D&file=0