Question about RCA P52960 52" Rear Projection Television

1 Answer

No power at all. just clicks.

Just recently I have had this problem. Tv got unplugged. Went to plug it back in, no power, i just hear a clicking noise from the right side bottom if you were to be watching it from front. I have never had anything go wrong with this tv. I really love this monster. Can you help me solve this issue.

Posted by looce on

  • looce Oct 08, 2007

    service number p52960yx1, chassis number ptk195y06b. Is this part expensive and can anyone replace it? thank you sir.

×

Ad

1 Answer

Vista Electronics

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,694 Answers

IHVT AKA flback xformer bad.For part #, please provide service # (YX01 on end of model?)

Posted on Oct 08, 2007

  • Vista Electronics Oct 08, 2007

    Part # 250694 or Asti Gen.2086

  • Vista Electronics Oct 08, 2007

    Not too expensive,but a technician should
    replace it.

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a RCA 42" model 42pa30rq and i was watching the tv and the picture goes out. I was trying to trouble shoot the tv on the y and x board but the x board is connected to the y board but still no type...

How much lld are you? How many Plasma sets did you repaired so far? Do you think repairing a plasma TV will be very like eating a ripe banana?
Contact any well experienced service technician; man.
"YOUR WORDS above REFLECTS YOUR IGNORANCE IN SERVICING SUCH ADVANCED TECHNOLOGY SETS.
What else to say? http://electronicshelponline.blogspot.com/
1helpful
1answer

While listening to music channel on uverse, the tv went black, no sound, clicking noise

usually clicking is bad capacitors or it could be a short on your power supply. Try unplugging power, wait 2 minutes, plug back in. If it still clicks, you can look inside for bad caps.. =
http://www.fixya.com/support/r5000889-repairing_tv_just_clicks_over_over
Let me know if I can be of further assistance.
0helpful
2answers

Tv just makes clicking noise and doesn't turn on

I had the same problem. The power board for the on-off had to be replaced. The set is only 11 months old.
0helpful
1answer

My TV does not power up when the power button is pressed.

It's sounds like your lamp or backlight has went out, I suggest reading your manual for service info and look online for a local repair shop.
0helpful
1answer

TV will not turn on.

hello..i think you have very big problems inside on you're TV you need a Electronics Technician to see inside the real problem.my tips is located in Power Supply Regulator..Can i know what kind TV Model???thanks

0helpful
1answer

Sony KT-T25SF8 Dead, no video or audio, low level clicking noise

Most likly the Horizontal output transistor has shorted out because of cold solder connections on the flyback transformer, and or a bad capacitor in the sweep power supply and or, a bad flyback transformer. If the set Did not blow the fuse, then mopst likly you will have a problem in the main power supply where several parts in a kit form has and should be replaced all together.
2helpful
1answer

Mitsubishi VS-6041 60 in. doesn't power up

Hello Tremulant

This denotes a possible problem with the Low or high voltage power supplies. The clicking you here might be the shutdown circuit acting because of excessive draw of current. The problem will most likely be associated with the HV power supply, but you will have to have a qualified TV technician check your TV to make sure.

I hope this helps,

Thank you,

Shuttle83
0helpful
1answer

No picture

Bad IHVT ( flyback transformer)--need complete service
number off back for part #-----------Let me know...T.
0helpful
1answer

Constant clicking every half-second as soon as you plug it in.

I have the same problem-still troubleshooting...so far still not find the cause. DM1 power supply output voltages are operates correctly. Signal output of microprocessor up and down (no good) that turn on Q14105 and latch optical isolator U14102 to power the unit but both of ohmed out ok. it hard to troubleshoot the main board with power on.
Not finding what you are looking for?

Open Questions:

See all RCA P52960 52" Rear Projection Television Questions

RCA P52960 52" Rear Projection Television Logo

Related Topics:

65 views

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76625 Answers

Cindy Wells

Level 3 Expert

6280 Answers

Paul Bade

Level 3 Expert

1688 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...