DISPLAY MY PHONE'S DISPLAY IS SHOWING RED COLOR TONE I HAVE SEE ALL THE IMAGES IN DIFFERENT COLOR FROM THEIR ORIGIONAL COLOR.e.g.I SEE ALL TEXT IN RED COLOR BUT BEFORE THE PROB I SAW THEM BLACK. ALTHOUGH I CHANGE COLOR PALLETS SETTING BUT THE RED COLOR TONE REMAINS.WHAT IS I SEE ON MY SCREEN HAS A REDDISH EFFECT.THE DISPLAY OF MY PHONE SLIGHTLY BLINKING TOO.

Oh vintage 386sx? In old graphics cards, there were DIP Switches to configure either to use as monchrome mode or color mode. Did you configure graphics card properly ? Moreover try using mode command to change monochrome to color.

Comparing Nikon to Canon or Canon to Nikon is like comparing Ford and Chev. They both do the job some swear by Chev while others swear at them same with Ford. Yes I've noticed a slight red bias on my Canon gear but nothing that can't be corrected with a proper white balance. To me Nikon had a more unflattering skin tone and I was and still do tweak the color in an image editing program.
I use many different digital cameras in my work and personally own four different major manufacturer digital camera systems.

Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.
Press POINT DOWN button to move a red frame pointer to the
item that you want to adjust. and then press SELECT button.
The level of each item is displayed. Adjust each level by
pressing POINT LEFT/RIGHT button(s).
Move a red frame pointer to
the item to be selected and
then press SELECT button.
IMAGE ADJUST MENU
IMAGE LEVEL ADJUSTMENT
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Contrast
Brightness
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Gamma
To store manually preset image, move a red frame pointer to
Store icon and press SELECT button. Image Level Menu will
appear. Move a red frame pointer to the Image 1 to 4 where you
want to set and then press SELECT button.
Image Level Menu
Move a red frame pointer to any
of Image 1 to 4 where you want
to set and then press SELECT
button.
Store icon
Press SELECT button at this icon to
store the adjustment.
IMAGE ADJUST
Menu icon
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Red)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White

This is known as laser scanner contamination and will require servicing. You can try running calibrations under the system setup menu/print quality/calibrate color/calibrate now. run a couple of these. You can also try an nv ram

Try doing a hard or reset or nvram:
1. Turn the printer off
2. Hold down the right arrow and the cancel button
3. Reboot the printer while holding the buttons and hold until permanent storage is displayed. Let go of the buttons and wait for the ready message on the display.

Good Luck,

Al
[email protected]

that may be because of a bad connection with the harddrive thats easy to fix you just take the harddrive out and blow the connecting surface clean then it should behave normaly agian:)

Is it possible your out of the 3G network when the origional messages were sent? If you have red bars the text wont come through until you get a good signal= yelllow or blue.

Go into your text message settings and look over each option very carefully. It may be set to "No Notifications".

Hi,try this: in the printer driver choose imaging and find "color reproduction" button. Just adjust that balck and gray will be printed FROM BLACK TONER ONLY(print black text and graphic from black toner only)

Regards

it's because the text alerts and alarms etc. all require a different file format than what the presets are...notice the preset tones already on the phone are ".mmf?" well most downloaded/bluetoothed/purchased ringtones are mp3s, not mmfs. i have the same phone..and i am fed up with this stupid problem. i don't know how to convert the file type..sooo i guess we're stuck at stupid.

ATTENTION ANY SYNC OFFICIAL READING THIS:
i hate you.

check there is power in machine. bye