Question about Dream Maker Spas Dream Maker Ez Spa Hot Tub

1 Answer

All controls work but the button to turn on jets. Jets will run if temp attire is turned up.

Posted by Trish bolyard on

Ad

1 Answer

Mike Tellegen

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dream Maker ... Master
  • 1,631 Answers

Bad Jets button on the topside controller panel - need new panel

Posted on Jan 29, 2014

Ad

2 Related Answers

tunde007

Tunde Autos

  • 2382 Answers

SOURCE: X-Spa 300, winterized for 3

Hi, you can try out any serviceman you know around you to run a quick diagnostic, but i know for sure they have their own service men that run diagnostics for them and if your display is dead as you said, i would have also recommended that you should change the LB70 because that is the only way to fix the dead display on it..

Posted on Sep 30, 2010

Ad

Kieran Ruppert

  • 990 Answers

SOURCE: I have a 5 year

This is probably a bearing problem with your motor. On a above ground spa five years is a long life.
You should be able to find two main valves to shut and stop water from draining. Then open the unions on the suction and discharge of the pump. It will probably be bolted down. If you can bend your arm ten ways getting these bolts off will be no problem. If you can't swear a lot. These are for shipping so you don't need to replace them all. Remove the pump and pull the wires or unplug from main box. You can take this to a pool shop or a motor shop and get a new one. They will do all the work cheap or for nothing and just charge for the motor and parts. When you remove the unions on the pump don't loose the "O" rings, often they can be tough to find to replace.

Posted on Oct 14, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have an Emerson model # R63MWENA-4727 on my Hot Tub. Runs continuesly fine. But when I turn the jets on I hear a " click" and it won't run.


It is a problem in the relay of that one motor in your spa electronic control most likely. If you have many jets buttons, you can unplug 1 pump from the control and plug in another relay see if the motor works.. if it doesnt work it your motor if it does work then its the relay in the controle system.

Sep 04, 2015 | Emerson Pool & Spa

1 Answer

My intex pump jets won't reset or turn off the heater is on but so are the jets can't get jets to go off unless unplugged then you lose the heat.


Sounds like bad controller?

Do you still have problem?
Use Comment link on this thread, and inform this forum what you may gave done this far?
Did you fix it? Did Intex help? What was problem?
if not...
Support Intex

Dec 23, 2014 | Intex Pool & Spa

1 Answer

When the pump is plugged in the heater an jets run the jets won't turn off


Sounds like bad controller?

Do you still have problem?
Use Comment link on this thread, and inform this forum what you may gave done this far?
Did you fix it? Did Intex help? What was problem?
If not...

Support Intex

Dec 22, 2014 | Intex Pool & Spa

1 Answer

Every time I put the heater on the jets turn on wont go off unless I turn the heater off.


some more infromation would be great, but the jets turn on to run water through the heater to heat the water, do the jets turn off once the water has heated to the thermostate set point.

Dec 20, 2014 | Intex Pool & Spa

1 Answer

Aqualux whirlpool bath


The panel has failed and it is unlikely that it was your dogs fault.

Dec 02, 2013 | Washing Machines

1 Answer

Our 880 Marin hot tub is constantly running the jets on 1/2 of the tub as if the circulation pump is running. The icon on the control panel does not show the jets are on. When we push the button to turn...


sounds to me with a power surge you could have a relay on the circuit board not working properly.
You will most likely need to change the circuit board to correct the problem.

US Parts Center

Sep 22, 2013 | Pool & Spa

1 Answer

Balboa VL700S control panel jets 1 not working


Your problem is going to be in the circuit board in the spa control box under the skirt.
You have a bad relay.
Rod
US Parts Center

Jun 25, 2013 | Pool & Spa

1 Answer

Jacuzzi Laser II: Problem with the Heater/filter setting. The jets come on when it's on this setting. When I turn it to Filter setting it's fine..when I turn it off the jets come back on What gives?


The jets will run while in the filtration / heating mode. If the spa is in the middle of the filtration cycle, the jets will stay on until the cycle time runs out. So, if the spa jets are on during this time, they are on for the full duration, 2-6 hours every 12. You can cycle the jet button to high, but when you try to turn them off, they will just go back on low.

Jan 23, 2010 | Jacuzzi Cyget In Ground Pool Pumps

Not finding what you are looking for?
Dream Maker Spas Dream Maker Ez Spa Hot Tub Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dream Maker Spas Pool & Spa Experts

john h

Level 3 Expert

23515 Answers

Vincent G
Vincent G

Level 3 Expert

2363 Answers

Tom Chichester

Level 3 Expert

61169 Answers

Are you a Dream Maker Spas Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...