Question about Video Cameras

Open Question

Panasonic Video Camera VX30

Fast Forward & rewind not working properly. Play ok.

Posted by Darayus - 1 on

  • apentengasan Nov 20, 2009

    I'M TRYING TO FIND INFORMATION ABOUT PANASONIC MODEL NUMBER NV-VX30A

×

Ad

5 Related Answers

Kimi

Kimi

  • 277 Answers

SOURCE: The unit will fast forward and rewind, but won't play

This is a problem with the process called 'tape loading' - pulling the tape loop out of the cassette and wrapping it around the spinning video drum, engaging the capstan and pinch roller and reel rotation. Check all the belts above and below the deck. Belts can appear to be firm but if they do not return immediately to their relaxed length when you stretch them 25%, they will need to be replaced. With the cover off, observe the behavior when you hit play. (You may need to put a piece of cardboard over the cassette to block external light from interfering with the start/end tape sensors). Assuming this is a basic VCR (no instant start features), you should see: 1. The video head drum begins to spin. 2. the roller guides move smoothly on the tracks, wind the tape around the drum, and stop snuggly pressed against the 'V-stopper' at the end of the tracks. 3. The pinch roller moves into position and presses the tape against the capstan. 4. The tape begins to move and is wound up by the takeup reel. 5. The picture and sound appear on the TV. With a 'rapid or quick start' (or it may be called something else) transport, the tape moves to a half-loaded position when the cassette is inserted. This is at an intermediate position partially pulled out of the cassette but not wrapped around the drum. On VCRs with a real-time counter and/or index search capabilities, the tape will be in contact with the control head. With an 'instant start' transport, the tape will fully load around the spinning drum when the cassette is inserted but the capstan will not engage and no tension will be applied to the tape until you press PLAY or REC. (After about 5 minutes, the drum will stop and it may unload to the half loaded or unloaded position.) Note that for VCRs with a real-time counter and/or index search capabilities, the tape must be in contact with the control head (but not the video heads) for all relevant modes. These VCRs (which include many modern units) must therefore pull the tape at least partly out of the cassette. In all cases, the completion of the sequence results in approximately the same mechanical configuration during PLAY. Several likely possibilities when it shuts down: 1. Everything occurs as above, picture and sound appear for a few seconds, but then the VCR unloads the tape, ejects the cassette, goes into REW mode, stops, or shuts off. Two common causes: The takeup reel does not turn and tape spills into the machine. This is sensed by the microcontroller which aborts record or play and attempts to save your valuable cassette. Most likely cause: old/dirty idler tire. As a test, turn the idler tire inside-out. The fresh surface will now work well enough to confirm this diagnosis and will continue working long enough for your replacement idler tire to arrive. See the section: "General guide to VCR cleaning and rubber parts replacement". The takeup reel is turning properly but

Posted on Nov 22, 2005

Ad

Anonymous

  • 579 Answers

SOURCE: VHS tape was playing . After stoping does not play. Other tape will play

The idler wheel (that only drives the tape in play or scan modes) is slipping too much (very common problem). Try verify this by putting the tape in play then immediately press the fast fwd or rewind buttons to scan the tape. On older machines, the idlers used rubber friction tires - on newer ones, a clutch. Either replace the tire or increase the spring tension on the clutch.
Hope Ya Fix It.

Posted on Jan 22, 2008

Ad

Anonymous

  • 71 Answers

SOURCE: Won`t Rewind

Do you still have the remote control? Try with the remote. If this works, the button of the camera is broken and have to be replace by a qualified technician. Good luck!

Posted on Nov 24, 2008

Anonymous

  • 3 Answers

SOURCE: My camcorder will not play, rewind or fast

what is your model number

Posted on Nov 30, 2009

javer821

Javier Gonzalez

  • 207 Answers

SOURCE: Sony BM-147 transcription unit rewind/fast forward problems

Hello just get a really cheap foot pedal replacement at http://www.tvps.com/Products/ECS-Sony-IN-75-Heavy-Duty-Foot-Pedal---Pre-Owned__ECS-PIN-75.aspx

Posted on Jan 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model mp820 mp3 player. how do I fast forward?


Cheapo MP3 play with rewind and fast forward - Tablets and e ...

forums.digitalspy.co.uk/showthread.php?t=1687936
Digital Spy Jul 5, 2012 - 13 posts - ‎2 authors
Cheapo MP3 play with rewind and fast forward Tablets and e-Readers. ... can anyone recommend a cheap MP3 player that will allow you to fast forward, ... the yepp yp55 t had a wonderful "scroll through" function that took ...

Oct 20, 2015 | Coby Audio Players & Recorders

1 Answer

How do I get fast forward & rewinds to work on my Teac W450-R dual cassette deck..?


Check the belts, inside the unit you should see a rubber belt which is what pulls the tape fast forward or rewind. Some belts with time get loose and slip, they can also break and fall off which will not let you fast forward or rewind.
Open your cassette player and look where the plastic pulleys are located and check for the belts, they might not be broken at all but very loose and slip on the plastic pulley.

Jun 07, 2015 | Teac Audio Players & Recorders

3 Answers

Hi, I am seeking the region free code for a Samsung DVD-D530? Thanks!


I tried the above steps, but each time when restarting the DVD player, it said 'reset' and asked for the language to be selected again. Pressing the "Fast Forward Fast Rewind Fast Forward Up Down" sequence caused the player to lock up and require powering off at the wall.
I found on another web site that there are different initial sequences. Once I use the one for Region 2, it worked fine.

I found the instructions below on another web site, but it worked for me...
  • Make sure there is no disc in the player.
  • Turn on the player (you can use remote control or front panel, it doesn't matter)
  • Wait for "No Disc" message to appear on the TV screen.
  • Press the Repeat button on remote (plain, not A-B).
  • Press the correct sequence of buttons of remote according to the original region code of your player (it's on the sticker on the back panel of the player). FF = fast forward, FR = fast rewind.
    • Region 2 players: FF, FR, FF, UP, DOWN
    • Region 3 players: FF, PLAY, FR, UP, LEFT
    • Region 4 players: FR, PLAY, DOWN, DOWN, RIGHT
    • Region 5 players: FF, UP, DOWN, STOP, RIGHT
    • Region 6 players: LEFT, RIGHT, RIGHT, PLAY, LEFT
  • If you pressed the correct sequence, a small white number 0 will appear somewhere on the top right of the screen. The white number 0 of the same font and size as the "No Disc" message, so don't confuse with the red "not allowed" sign that would appear when you press a function that's not available.
  • Turn the player off and on again, then you can pop in a DVD of any region and watch immediately.
Good luck!

Apr 30, 2011 | Samsung Televison & Video

1 Answer

The dictaphone wont rewind or fast forward and makes a bleeping noise


Hi,
Does the tape move when you press rewind or fast forward.
If the tape moves for a few seconds then bleeps it sound like a sensor problem.
If it only bleeps when the rewind and fast forward are pressed and the play is ok it sounds like the actuator motor is faulty,this motor enables the rewind and fast forward.
Hope this helps.

Dec 07, 2010 | Dictaphone 1740 Desktop Cassette...

1 Answer

JVC VRC MACHINE HR-S7965 Rewind/fastforward cog slip noise


maybe a broken break band on reel supply (left one) in the vcr !!!

Apr 22, 2010 | JVC HR-J461MS VHS VCR

4 Answers

How do you unlock the Samsung DVD - P191 from all regions?


The following solution was posted on Whirpool.

Turn on the unit with no disc in the unit. The No Disc message should be visible
Press the following keys in this sequence
Repeat (not the A-B Repeat, just the plain Repeat)
Fast rewind button (just below the Disc Menu button)
Play button
Down button
Down button
Right Button

The number 9 should now appear towards the left of the screen.

Open then close the disc draw

Turn off the unit and then on again. You should now be able to play DVDs from any region

Apr 18, 2009 | Televison & Video

1 Answer

Numark CDX Search (for fast forward and rewind) not working.


Possible switch fault or servo problem,if you havent had it repaired you can send it to us.

Regards.

http://www.audiovisualservices.info/

Nov 15, 2008 | Nu Mark Numark Cdx Table Top CD Player CD...

4 Answers

VHS tape won't play or rewind


I work at the History Channel and have  a VHS that had the same troubles. I need it desperately for the show I am working on. I tapped it on a table fast forwarded it and presto! Tape fixed, crisis averted. Thank you, Thank you, thank you.

Feb 28, 2008 | Televison & Video

2 Answers

VHS tape was playing . After stoping does not play. Other tape will play


The idler wheel (that only drives the tape in play or scan modes) is slipping too much (very common problem). Try verify this by putting the tape in play then immediately press the fast fwd or rewind buttons to scan the tape. On older machines, the idlers used rubber friction tires - on newer ones, a clutch. Either replace the tire or increase the spring tension on the clutch.
Hope Ya Fix It.

Jan 20, 2008 | Televison & Video

Not finding what you are looking for?
Video Cameras Logo

Related Topics:

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Video Cameras Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Al Rush

Level 2 Expert

270 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Video Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...