WHAT DOES FLASHING POTS & PANS X1 FOLLOWED BY NORMAL WASH FLASHES X3

This sounds like a door switch that is faulty on your main door so the system gets a signal saying its not closed properly and there for signals fault

what is your model number is then we can get started then

Hello,

To reset the dishwasher push in this order the,

HIGH TEMP WASH- HEATED DRY- HIGH TEMP WASH- HEATED DRY - CANCEL/OFF

the control will be reset...but more importantly how many times in a row does the light flash..it will indicate what error code its displaying??

example if it flashes 4 times then a pause then flashes 4 times again its displaying the error code#4
7 flashes then pause then 7 flashes its displaying the error code#7 ect ect



GENE

The red light tell you there is a fault. You have to read the fault code and it will give you a general idea of the problem - to do this you have to enter the service mode of operation - close the door and turn the dishwasher on.
The Start/Stop light must be blinking. If the Start/Stop light is not blinking, press and hold
the Start/Stop button for at least 3 seconds to exit the cycle. The Start/Stop light should now be blinking.

Press and hold the Start/Stop button while turning the dishwasher on. Release the
Start/Stop button and immediately press it 2 more times. Flashing Intake/Drain and
Salt lamps and a lit Rinse lamp indicates successful accessing of services mode
Fault codes
F00 Pots & Pans Lit
F01 Sani Wash Lit
F02 Normal Plus Lit
F03 Normal Lit
F04 Economy Lit
F05 Rinse & Hold Lit
F06 Pots & Pans Lit
F07 Sani Wash Lit
F08 Normal Plus Lit
F09 Normal Lit Flashing

It sounds like the circuit bontrol board is cracked or shorted, which means it must be replaced.

I've finally tracked down the manual and it the fault code is as follows

"Indicates a fault in the heater or in the thermistor"

You can go into a fault tracing mode by pushing the "Rinse Hold" button five times within 15 seconds. The first, third, fifth and seventh lights will flash when in this mode and you can test the following parts by pressing the corresponding button. I'm going to try the heater test below and assume that if that works the fault must be with the Thermistor. The other tests could be useful for other faults.

User manual found here

Rinse Hold - tests detergent solenoid, detergent flaps open after about 60sec

Pots & Pans - tests Rinse Aid Solenoid, rinse aid will flow down door

Normal Wash - tests water inlet valve, water can be heard entering

Light Wash - tests ventilator solenoid, there will be a click followed by a rattling noise

Quick Wash - tests the heater, the element heats up, WARNING don’t touch element HOT

Temp - tests circulation pump, the pump starts

Dry - test outlet pump, the pump starts

Manual says to push 55 and 65 degree button to exit, I have no idea where those are so will probably just switch off at wall to reset.

Hope this helps someone. I rang ASKO and they said they didn’t know what the fault code meant so either they can’t read or their service sucks, probably a bit of both!

The dishwasher will not start. The following things have occurred;
1. The Cycle option light is flashing.

The model is GU2500XTPS3



Can anyone please assist if they have seen this problem before?

Try this solution first
Push the Hi-temp and then push the Sani-rinse. Go back and forth multiple times on these two buttons. I found that after a handfull of pushes that a "1" came up on the display. I continued to keep rotating the two buttons and then a "2" came up on the display and the dishwater started it's "drain" phase. I then hit cancel to clear and then I selected the cycle I wanted. The washer started up just as normal at this point.

shut off the power and see if the unit will reset. if its plugged in, it will be easy, look under the sink. if not, try a breaker.
let the power stay off for about a minute.
then back on.
if not restored, then you have logic boards that failed.
sorry,
good luck
mark

ga, behind the toe panel on the bottom there should be a tech sheet explaining how to put the dishwasher in the test mode. See if you can enter the test mode. If you can't, you probably have a stuck or shorted keypad. Catriver...post back