Question about Whirlpool GHW9150 Front Load Washer

1 Answer

Whirlpool GHW9150 washing machine

During the rinse cycle, I think, I'm getting a message of an alternating f and h on the control panel. Is this an error message and what does it mean? Also, can you recommend a website where I could download an instruction manual for this machine? Thanks, Duncan

Posted by nacnud on

  • Anonymous Nov 28, 2007

    flashing hp

  • Anonymous May 09, 2008

    I get f4 now it won"t drain

×

Ad

1 Answer

prem mathew

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Click on Whirlpool (below FIXYA)on this website, type in your model No & search. You will get a shortlist; click on your model,below the page u will get Manual/Guides. Click on the blue, voila! u hv your manual on line.

Posted on Oct 05, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NF error code during rinse cycle only.


If the unit was working fine before bearing repair, then I lean toward wiring issue. Do a visual inspection of the water valve and all the wires to it. One might have been put in wrong place. If wiring is correct, then maybe a bad water valve. The water valve has multiple solenoids and the one for rinse might be bad. I still think its a wiring issue. Good Luck!

Nov 23, 2015 | Samsung WF337AAL Front Load Washer

1 Answer

3E error during rinse cycle on Amana NFW7200TW washer


E3 Error: Machine control is attempting to drive the motor but is not seeing any tach response. Visual check shows motor is not moving. (Locked, Hall Sensor fault). The hall sensor is a circuit in the motor. the motor will need to be replaced. Here is a link to the motor.

Oct 18, 2012 | Amana NFW7200TW 3.5 Cu. Ft. Front Load...

1 Answer

F&P GWL11 Washer Stops at rinse - Error Code 37


I hate to say it but it sounds like the controller. I used to have one that had a similar problem that was fixed with a diverter and a controller. Another year or two later it was doing the same thing, so we just replaced it. Just a warning.

Jul 08, 2012 | Fisher and Paykel Washing Machines

2 Answers

My samsung washing machine model WA13513 13.5kg load had 8E error message popping out from the screen. Is the computer board damaged?


OVER CURRENT ERROR – Display shows 8E. IPM fault signal (this is caused by the overload of the MICOM INTO during motor action).
IPM: Integrated power module. The IPM controls the motor.
If the fault (low signal) happens to be sensed even once during the washing/rinsing stage, the motor stops immediately. However, during the dehydrating stage the signal is to be sensed, when the number of signals reads more than 6 per 500ms during the Washing or Rinsing cycle action.
If the motor stops working, in one direction ten times, “8E” Error is displayed.
During dehydrating, when the overload is sensed, the motor stops working at once and then feeds back to the initial stage of the dehydration unbalance sensing. When the feed back has occcurred twice, Error “8E” is displayed during the dehydrating unbalance sensing, No error happens by overload sensing. When it happens at more than 800rpm, the process is stopped compulsorily. Power SIW OFF can clear the overload error.

would advise calling a tech... hope this helps.
-->

Oct 25, 2009 | Washing Machines

2 Answers

E 31 error message on Haier HW1000


E31 Motor
The feedback signal does not change in 8 minutes during the motor runs <-- Bad translation that probably means bad sensor or electronics issue.

Call repair people and then get a new machine sent if still under warranty.

Jun 01, 2009 | Haier HWD1000

1 Answer

Washer fills slow only in the rinse cycle


Need a model # to get exact part you will need at rinse most washer go straight cold so I would say water inlet valve if humming sound is present

Apr 28, 2017 | GE WBSR3140DW Top Load Washer

Not finding what you are looking for?
Whirlpool GHW9150 Front Load Washer Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18378 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...