Hoover AAA140 Front Load Washer Logo

Related Topics:

Question about Hoover AAA140 Front Load Washer

Open Question

Flashing lock light on hoover dyn8144d display

Flashing lock light the machine wont work at all

Posted by Anonymous on

Ad

2 Related Answers

Anonymous

  • 8619 Answers

SOURCE: Hoover Nextra HNF2127 washing machine. Lights flashing at finish

Hi


Thanks for using FixYa. The start and pre-wash usually flash due to a clogged drain hose or the water pump. You’ll need to drain the water out of the base and also check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine). If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Posted on Feb 18, 2010

Ad
caroldon

Donald DCruz

  • 17130 Answers

SOURCE: hoover DYN8144D

It ispossible that the machine does not start off the cycle because there are errorsdue to feedback from the inputs. For the program to start up the main programcontroller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting fromthe flow of water into the drum as also the drain valve to open to exit thewater at the point of the program cycle. If this does not happen then thevoltage at the valve/motor/pump must be checked or the fault relates to novoltage from the controller. This meansthe controller is a suspect.If thewater flows though the inlet then the flow pressure should be good, if not theinlet valve is bad or there is dirt in the filter. Also check the flow at theinlet of the water line. Once the water comes into the system the WATER LEVELSENSOR - normally a pressure switch- must activate at the preset/chosen levelto give the signal to the program controller to switch on the motor. What ismost important for the motor to start functioning is that the door switch mustbe ON when the door is shut or this will be an error for starting the motor forrinse and wash.Check thislink to replace the inlet valve:http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html Finallyafter the wash the drain valve will be activated, the water is allowed to comein to rinse and then finally the dry spin with the drain valve/pump activatedso as to drain off all the water from the clothes during the spin.Make surethat a fault in any of the cycle will relate to the specified action, so checkthe command from the program module and then the executing device be it thevalve or motor or pump. Please check the link below:http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Posted on Jul 06, 2012

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My hoover dynamic 8+ washing machine Model number DYN8144D-80D displays an E08 error Code

E08 is the motor speed sensor error code. Suggestion: Try a cycle with very few garments and see if it completes the cycle.
0helpful
1answer

Hoover dyn9144dg washing machine door lock flashing wont start.....lock changed still wont start.....light still flashing

Hello the
Plesre and welcome to fixya
can i ask you a question did you unplug the machine and leave it sit for at least 1 hour
See these machines have a internal computer that stores information like any settings that are in the programed in the machine
It normally takes any where from 45 min to at least 1 hour to compete the memory loss on the computer thus resetting the computer ok
so please tell me if you did this if so there is more that we can do ok
Best regards michael
0helpful
1answer

Hoover nextra washing machine door wont lock / cycle start

sounds like the door lock mechanism. if this cannot signal it has engaged, to the board, no other function will work (you don't want the washer going with the door open, trust me :) )
1helpful
1answer

Machine wont sart

Your door lock/latch is broken, this is a common issue with front loading washing machines and the only way to fix it is to replace the door switch.
0helpful
1answer

Hoover dst 10146p fault

Ken did you solve this problem with the machine as mine has just started to do the same thing, thanks
17helpful
2answers

After a power cut my washer wont work the door security light just keeps flashing! Model Hoover Vision HD

Ihave a Hoover Vision HD washing machine and the "Door Security" light keeps flashing. I have looked in the manual and it says the door is not properly shut. However the door is correctly shut and as a result the machine will not operate . The door will open or close but will not start a cycle to wash. Any suggestions please????
2helpful
2answers

Hoover Nextra HNF2127 washing machine. Lights flashing at finish

Hi


Thanks for using FixYa. The start and pre-wash usually flash due to a clogged drain hose or the water pump. You’ll need to drain the water out of the base and also check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine). If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee
16helpful
3answers

Hoover HNL7166 'Start Delay' light flashing

Hoover (Nextra series) washing machines

The 'Start' & 'Pause' LED's will flash together to indicate the error code. You have to count the flashes within each 15 second period to get that error code. The start and the pause LED's will flash together at 1Hz (i.e 1 flash per second) within that 15 second time frame, then will continue and show again within another 15secs and so on.

1 Flash = Interlock fault
2 Flashes = Fill time-out
3 flashes = Drain time-out
4 flashes = Overfill fault presure pipe blocked
5 flashes = NTC error
6 flashes = faulty control board
7 flashes = Motor jammed
8 flashes = Tacho fault
9 flashes = Motor triac on module board
10 flashes = Prog Selector or wiring fault
Not finding what you are looking for?

800 views

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

W.L.

Level 3 Expert

2511 Answers

Steve F

Level 3 Expert

1361 Answers

Mike

Level 3 Expert

4383 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...