Question about Dymo LetraTAG Thermal Label Printer

3 Answers

Dymo letra lable maker,

I can't figure out how to change the ink.

Posted by berry05 on

  • 4 more comments 
  • ASPECK Feb 18, 2008

    Printing is faint when I make a label (parts of letters don't even appear...very faint ink on other parts of the label). Since it still prints SOME of the text, I assume the batteries are still working, and the tape is about 3/4 full so neither of the suggested fixes I've seen on line (change batteries, change tape) would be an appropriate solution.

  • Anonymous Dec 03, 2008

    same thing happens to mine...new batteries, full tape...no printing, the roller is moving fine...the magnetic/heat pad moves in and touches the tape fine...can't figure it out.

  • rayken Jan 25, 2009

    Our Dymo Letratag prints the bottom half of the words, it doesn't matter what size the letters are. The machine is almost new. We've tried new batteries and new tape. It must be something wrong with the print head.

  • Anonymous Mar 10, 2009

    did all those things and it worked, thank you

  • blotch Mar 13, 2009

    I changed the batteries and the tape -- didn't work for me either.

  • Daniel Krenn Feb 01, 2013

    Definitely just put decent batteries in it. I promise this will work.

×

Ad

3 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There is no ink in the letratag. just replace the tape and/or the batteries.

Posted on Dec 19, 2007

Ad

Anonymous

Neither of those work,, Try again

Posted on Apr 08, 2008

Ad

Anonymous

If your model is the Dymo Letra Tag XR, just change the batteries.

Posted on Oct 24, 2007

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP PRINTER C6280 problem says ink system failure error 0xc18a0001


Reset the printer:
With the product turned on , disconnect the power cord from the rear of the product.
Wait at least 15 seconds.
Reconnect the power cord to the rear of the product
Remove, clean, and reinstall the printhead
remove ink cartridges
Figure 22: Lift the latch handlec01481823.jpg
Lift the printhead straight up to remove it.

Figure 24: Three areas to cleanc01481825.gif 1 - Plastic ramp on the side of the ink nozzles
  1. Figure 29: Clean the electrical contacts inside the productc01676244.gif
  2. Dry the area with a clean, dry, lint-free cloth.
Reinstall the Printheads and the cartridges

Reset the product

It should work otherwise try to replace the Printhead and instead change the entire printer its time to change it

Feb 26, 2011 | HP C6280 All-in-One Printer

1 Answer

My printer keeps on blinking error for no ink and


If by "just changed the ink "you are trying to say that you have just recharged you printer's cartridge then don't put this question to yourself because this happens when the printer figures out that the cartridge is not original!

Dec 19, 2009 | HP DeskJet F380 All-In-One Printer

1 Answer

I do not know how to change the black ink on a monolta 2300 ?


http://crm01.konicaminoltaeurope.com/openmind/technic/engineer/qmspubkb.nsf/0/70744652a954e650c1256f820078e0a2/$FILE/MC24x0-Replace%20Toner%20Cartridge.pdf
Goto the above link and it shows the PDF doc. for changing the cartrides.

Jun 23, 2009 | Konica Minolta magicolor 2400 Laser...

1 Answer

I cant figure out how to change the ink cartridges on my lexmark


On an X4850 the whole top of the printer opens up to reveal the cartridge carriers. Press down on the latch of each side to reveal the cartridges.

Here is a link to the User guide: X4850 User Guide It is described on page 94.

Nov 19, 2008 | Lexmark JetPrinter X1185 All-In-One InkJet

2 Answers

How to change black color inkonHp2175all in one


Supported HP ink cartridge part numbers The HP PSC 2100, 2170, and 2200 all-in-one series products use the ink cartridges listed in the table below. The HP 58 tri-color photo ink cartridge replaces the black ink cartridge for six-ink photo printing. Ink cartridges Part number HP 56 black ink cartridge (19 ml) C6656A HP 57 tri-color ink cartridge (17 ml) C6657A HP 58 tri-color photo cartridge* (17 ml) C6658A HP 27 low capacity black ink cartridge (10 ml) C8727A HP 28 low capacity tri-color ink cartridge (8 ml) C8728A * Replaces the black ink cartridge for six ink photo printing and includes cartridge holder. Replacing the ink cartridges The power must be turned ON to the all-in-one or the print carriage will not come to the center.
  1. Locate and raise the print cartridge access door on the front of the unit, just above the output tray. The print cartridge carriage will move into the middle of the access area. Figure 1: Raising the front access door and the ink cartridge latches c00224418.jpg
  2. Press down lightly on the top of the ink cartridge latch of the ink cartridge to be replaced and then pull the lower section of the latch toward you to unlatch the ink cartridge.
  3. Grasping the sides of the ink cartridge, pull the cartridge toward you to remove it as shown in Figure 2. Figure 2: Removing the cartridge after raising the latch c00224419.jpg
  4. Remove the replacement cartridge from its packaging, and touching only the black plastic, gently remove any tape covering the nozzles. Do not touch the gold-colored contacts. Figure 3: Removing the protective tape c00224420.jpg
  5. Holding the ink cartridge with the printed label up, slide the cartridges one at a time into the print carriage as shown in Figure 4. The black ink cartridge (HP 56 or HP 27) goes on the right side (with the gray latch) and the tri-color cartridge (HP 57 or HP 28) goes on the left side (with the blue latch). If the optional photo cartridge (HP 58) is installed for six-ink photo printing, it is installed in place of the black ink cartridge. Figure 4: Inserting the cartridge c00224421.jpg
  6. Place your hand on the latch as shown in Figure 5, with the thumb pulling the end of the latch toward you. While holding the end of the latch out, press down on the top of the latch until it stops and then release the lower portion of the latch with your thumb so that it catches under the tabs. Do not force the latches into place or damage to the unit might occur. Close the all-in-one after latching the ink cartridges in place. Figure 5: Latching the ink cartridges in place c00224422.jpg
  7. Close the print cartridge access door.
  8. A message will appear in the front panel display requesting that the ink cartridges be aligned. Press ENTER on the front panel to start the cartridge alignment. Two pages will print. Following the instructions printed on the second page, place the first page on the scanner glass in the lower-right corner and then press ENTER to finish aligning the cartridges. Remove the page from the scanner glass when complete.
Storing the option photo printing cartridge while not in use The optional photo print cartridge (HP 58) that may be purchased separately for six-ink photo printing includes an ink cartridge protector. The protector is designed to keep the photo cartridge from drying out when it is not in use and for holding and protecting the black cartridge when the photo cartridge is in use.
  • To insert a cartridge into the protector, slide it into the protector at a slight angle until it snaps in place.
  • To remove a cartridge from the protector, push down and back on the top of the protector to release the cartridge and then slide the cartridge out of the protector.
Figure 6: Inserting and removing ink cartridges from the ink cartridge protector c00224423.jpg Fixing error messages that appear after changing a cartridge After inserting the cartridge, one of the following messages appears:
  • Check the black (or color) cartridge
  • Replace the black (or color) cartridge
  • The wrong black (or color) cartridge is installed
These messages indicate that the ink cartridge is not making good electrical contact, is bad, or is the wrong cartridge. Complete the following steps to diagnose and correct the condition:
  1. Open the front of the unit to access the print cartridges (as shown in Figure 1).
  2. Remove the ink cartridge indicated in the message and inspect it.
  3. Verify that it is the correct part number and if it is, reinsert it.
  4. Close the lid to see if the problem is corrected.
  5. If the message is still displayed after a few seconds, remove the ink cartridge again.
  6. Unplug the power cord from the back of the unit.
  7. Clean the electrical contacts on the ink cartridge with a soft clean cloth, slightly dampened (not wet) with clean water. Each contact is very small and shaped like a rounded square. Figure 7: Cleaning the cartridge contacts c00224424.jpg
  8. Inside the HP all-in-one product, clean the contacts in the print carriage (the cartridge holder) with a clean cotton swab slightly dampened with clean water. Allow them to dry for five minutes before reinserting the cartridge(s) and turning on the printer. Figure 8: Contacts to be cleaned c00224425.jpg
  9. If the problem remains, replace the ink cartridge.
  10. If the problem still exists after trying all of the steps above, contact HP for assistance.

Oct 13, 2008 | HP Office Equipment & Supplies

1 Answer

How to change ink cartridge on a HP Officejet R40


Hai

Please click on this link, and you will find the instructions with Pictures to change the Cartridges

Change the INK Cartridges

Thanks
Riz

May 30, 2008 | HP OfficeJet r40 InkJet Printer

1 Answer

Changing ink cartridge


I need help, I have a canon MP530 just changed the cartridges, but it tells me to check ink. Is it necessary to fill the lg.space for another black cartridge for it to work ?

[email protected] thankyou

May 01, 2008 | Canon PIXMA MP780 All-In-One InkJet...

1 Answer

Can't figure out how to change ink in HP PSC 1410


heres the link for the manual for this printer , it will inform you
how to change the ink cartridges , hope it helps, just click here:
http://h10025.www1.hp.com/ewfrf/wc/manualCategory?product=441115&lc=en&cc=us&dlc=en&lang=en&cc=us

Mar 30, 2008 | HP PSC 1410 All-In-One InkJet Printer

4 Answers

Changing cartridges


Did you get the answer for how to replace the ink cartridge, because I don't have a manual myself and I can't even figure out where the ink cartridge is located?

Dec 11, 2007 | Office Equipment & Supplies

Not finding what you are looking for?
Dymo LetraTAG Thermal Label Printer Logo

2,068 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dymo Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

jdthefixer

Level 3 Expert

746 Answers

Are you a Dymo Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...