Question about RCA P61927 61" Rear Projection Television

1 Answer

Rca home theater problem

My rca home theater tv keeps jumping channels and the remote will not operate it the only way to operate it is to cut it off useing the button on the tv the channel button nor the volume buttons work just the on/off button.

Posted by jahnesha7 on

  • hdbadboy_rgv
    hdbadboy_rgv Aug 06, 2012

    Tech 8232 the solution with disconnecting the wire from middle board worked like a charm..Thanks!!

×

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 61 Answers

The trouble is the front panel buttons,unplug the unit and remove the back cover,just below were you removed the top screws,you can look under and see the top of the tubes,there is a small board in front of the middle tube,unplug the right top cable off this board and you can use your remoten till you can get it serviced

Posted on Mar 07, 2008

  • hdbadboy_rgv
    hdbadboy_rgv Aug 06, 2012

    Worked like a charm!! Thanks Tech 8232

  • hdbadboy_rgv
    hdbadboy_rgv Aug 06, 2012

    My television is an RCA P46924 rear projection.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Try to turn on via remote or button on set. Only a green flash on front. Nothing else. Can I fix it?


About 435,000 results (0.80 seconds) Search Results

    3 Ways to Program an RCA Universal Remote - wikiHow

    www.wikihow.com > ... > TV and Home Audio > Television

    wikiHow... Universal Remote. Are you tired of juggling three or four different remotes just to control your home theater setup? ... Log in via ... Turn on the device you want to control. ... Press and hold the button on the remote that corresponds with the device.... You will need to try another method in this article to program the remote.

    How to Program an RCA RCR312W Remote: 15 Steps ...

    www.wikihow.com > ... > TV and Home Audio

    wikiHowHow to Program an RCA RCR312W Remote. ... Log in via ... Press the PLAY buttonevery five seconds until the component turns off. ... If component does not respond or has limited functionality, codes in a different block list can be tried until you find the code that allows the remote to .... Set Up a Home Theater System.

    Your remote reprogramming woes solved - Rogers RedBoard

    redboard.rogers.com/.../your-remote-reprogram...

    Rogers CommunicationsJun 18, 2014 - Once the TV turns off, press the SETUP button once to lock the code.... You can always contact us via our Facebook page or tweet us ... Hi my TV is anRCA model # RLDED3258A-B I have tried 73 codes from Universal .... I have tried toset up my tv and home theatre with the Rogers remote but no luck...

    RCA TV: input channel/s-video - ecoustics.com

Jan 19, 2016 | RCA Audio Players & Recorders

2 Answers

I Need a remote code


Have you checked online with manufacturer of the remote? Remote codes are usually available.

May 08, 2014 | Frisby GPX HT219B Home theater system

2 Answers

Can you use dvd without speakers


Yes, go to your Television menu and system settings, select sound source and set it to internal speakers

Feb 15, 2014 | RCA Rtd3136 5.1 Channel Home Theater...

1 Answer

How do i connect my pc to my phillips home theatre system through an hdmi cable


The best way is to connect your laptop to a spare HDMI input on your TV first, then use the AUX OUT from your TV to the AUX IN1 of the Phillips Home theatre system using a standard RCA cable.
The only catch with this is that you will have stereo analog audio, NOT digital surround. However, by pressing the "SURROUND" button of your Phillips HTS remote you can switch the audio output to multi-channel surround, stereo or party mode.
What is the model number of the TV you are using?

Oct 23, 2012 | Philips HTS-3565 Theater System

1 Answer

No sound from tv, dvd, cable. Speaker test does work. Sound stopped suddenly when channel was changed.


What does this mean: "when channel was changed"? TV channel?? Would that mean a remote command was issued? How about FM (no external cabling)?

Page 23...
http://www.retrevo.com/support/RCA-RT2280-Home-Theater-Systems-manual/id/402ag600/t/2/

Sep 02, 2011 | RCA RT2280 System

2 Answers

The audio keeps going in and out and cuts off. Also I have other devices going into aux in but it doesn't show 5.1 surround it only shows the front L, Front R, and CT speakers in stereo. I want everything...


If you are playing a source that is Stereo such as FM Radio or a CD the sound will not use all 5.1 speakers unless you enable the correct Surround Mode. On the remote there is a button on the lower right of the remote that says SURROUND. You can toggle through the various surround modes with this button the mode you want is Dolby Pro Logic The Pro Logic mode uses the built-in circuit to steer the Left, Center, Right and Mono Surround channel audio signals and uses all five speakers to play both stereo and Dolby Pro Logic program source, such as TV and VCR. You can use this mode with any stereo program source (such as VCR/TV) to enjoy multi-channel sound experience.

Mar 02, 2011 | RCA RTD317W Theater System

1 Answer

Can't find a code to set the rca rtd315wr home theater system to dish network remote


We would be happy to help with that. Here is a list of someof the codes that we have for RCA home theater systems: 703, 852, 772, 638, 704, and 727.

Press and hold the AUX mode button until all mode buttons at the top of theremote come on, then release. Enter the number 2 then one of the codesfor your RCA home theater system provided above. Press the pound (#) button, the modelight should flash three times. Checkthat the code works by trying several different functions on the remote to makesure it will properly operate your RCA home theater system. Keep in mind that some codesmay not be compatible with your equipment. If this is the case, please try theother codes listed for that device until you find one that is compatible withyour equipment.

We hope this helps you, and thank you for being a valued DISH Network Customer!


Phillip Chang
DISH Network Customer Service Representative

Feb 23, 2011 | RCA RTD317 Theater System

1 Answer

Programing a remote eur7623x60


i have an emerson tv,an have not found a remote to work the tv,but,i have tuned it in to sky,by holding the channel and audio button up,it switched to av,so sky came in,all i can say is keep trying

Jan 16, 2010 | Panasonic SC-HT690 System

2 Answers

Have a converter box. Had to change battery in remote and now tv will not turn off.Have a rca tv


hold the power on off button down and press the channel up button repeatedly up to 45 times until the tv set turns off.

Dec 11, 2009 | Insignia Digital-to-Analog Converter for...

1 Answer

OLDER MODEL RCA HOME THEATER PICTURE AND PICTURE


Hi Unykue,

I am an electronics technician who just happened have been given the same set as you because it was giving the previous owner the same problem. Since I am confident in my trade, I took the set and diagnosed noise in the remote receivers input to the cpu.

What this means is that a capacitor( or something) wasn't working properly and was either not filtering the noise out or it was introducing noise into the data stream that controls the TV through your remote control.

My fix was to essentially cut out the entire remote control input to the TV. Since I have a directtv box to give me remote control, I don't care if the TV's remote works anyway.

The way I did this was to open up the unit and find the front I/O board were the buttons meet the switches for power,chaennel, volume, etc. On that board there is a plug with white wires and one black wire. The two wires to cut are the one next to the black wire and the one all the way at the other end of the black wire. These two wires are easy to splice back if you do not like the results of this procedure so that there is really no risk of damaging your set. If you wish to verify the proper wires to cut, they are the two wires that come from the IR receiver's side of the board YET DO NOT GO TO THE OTHER SIDE WITH THE BUTTONS! There is one wire that does indeed go to both sides.

This may not be a perfect solution but it is free. I hope that this will help someone out there.

Len

May 09, 2008 | RCA F32648 32" TV

Not finding what you are looking for?
RCA P61927 61" Rear Projection Television Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76407 Answers

matt martin
matt martin

Level 3 Expert

1258 Answers

Cindy Wells

Level 3 Expert

6121 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...