Question about KLH DVD8350 DVD Player

Open Question

Output right channel tv

Cant grt it hooked up to my tv, 98 modlr rca

Posted by jessica on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Trying to hook up an emerson dvd player to tv and its not working? older tv it has no cable hook up or control box for channel set up, shouldnt the dvd player still be able to work though?


IM GUESSING THIS MIGHT BE AN RCA TELEVISION? if you dont have an rca in hook up on the tv give up and buy a new tv or you can find an older item what it is is a switch that has an rca input and a coax output it was used to hook up the older video game systems it is still sold in most stores and that will work if you do have rca inputs and lost the remote you need to get a universal remote to switch the input on certain older rca tv's you could go to channel 00 and it would set it to the input with the switch you shoudl be able to use it by putting the tv on channel 3

Feb 28, 2010 | Emerson EWD7001 DVD Player

1 Answer

The box says these speakers work on TV's but they are not working with my T.V. Are they meant for just PC's?


Just check your tv might have audio setting to output sound though its speakers change to aux or diffent output aswell you should find it comes with 2 rca to 3.5mm jack if so plug rca into left and right rca then hook green or center channel to it make sure you go though you imputs on you steezza aswell

Oct 17, 2009 | Philips MMS 321 Computer Speakers

1 Answer

Auxillary channel for dvd


You need to determine what output options your DVD player has. Take a look at the rear of the player. It will certainly have RCA jacks for video and audio outputs (yellow for video, red and white for right and left channel audio). It may also have RCA jacks for component video (marked Y, Pb and Pr). Finally, it may have a threaded connector marked "out to TV" or "antenna out" or something similar. This is called RF output.

Most players today don't offer RF output because nearly every TV has direct AV inputs available. If your DVD player has RF output, connect the output connector to the TVs antenna input. You need a coaxial cable with F-connectors on the ends. One may have been supplied with the player. RF output is on channel 3 or 4, set by a switch on the back of the player or by its on-screen setup. Just set the TV to that channel to watch a DVD.

If your player doesn't have RF output, you connect it to the TV using the AV jacks. You need cables with RCA plugs to to connect the video and audio from the player to the TV. Then you switch the TV to its video input to watch the DVD.

This is where you might run into problems. Many TVs need the original remote control to switch inputs. (Some older RCA sets used channels 90, 91 and 92 to switch to their video inputs so any remote would work, but these sets were made before 125-channel tuning became standard. If your set is one of those models, those are the auxiliary channels you heard about.) If you can't switch the set to video input with front panel buttons and you don't have the right remote, you're not completely out of luck.

If you can't use your set's AV inputs or it just doesn't have any, you need an RF converter. These cost around $15. They take the audio and video from the DVD player and convert it to channel 3 or 4. Then you hook that output to your TV as described above.

May 17, 2009 | RCA Universal Remote Control

1 Answer

I have dynex flat screen hdtv,need to hook up jvc dual dvd-vcr recorder to it need direction pls have no knowledge of hooking up this diagram would also be great


  • find the video input 1 in the back of the tv (this video connector yellow + audio red **audio right channel and white left channel) is known as female RCA conector)
  • get a set of rca wires **known as male RCA*** (yellow red and white)
  • find the RCA female conectors Yellow red and white in the DVD call it video (and audio) output
Connect sets accordingly the TV video input yellow conector with video output yellow with the set of wires RCA yellow. Do the same with audio.

  1. second part of this talking is to find and cable splitter (usually three output and one input
  2. find TWO coax cables (this cable is usually a black wire with a connector each side this fits perfectly in the antena input of the tv)
Now connect your cable into the splitter (input) and your two cables in each output, then send one of them into the TV antena conector and another to the DVD coax input.

To watch your TV only select any regualr channel as you do it.
And to record and actually see Your DVD/tape and what you record also. You have to select in your remote control the video 1

ones you get custome to this configuration you can record a channel and at the ssame time watch any second channel selected in the tv.

I hope was clear.

Apr 21, 2009 | Dynex 20" Digital TV

1 Answer

How do i hook up my rca dvd to my samsung tv its hooked up right but i can'y figure out how to get the tv on the right channel for it to work


This DVD player only has audio and video outputs. You'll need to connect it through one of your TV's A/V inputs, then switch to that input to see the DVD signal.

If your TV doesn't have A/V inputs available, you'll need to connect the DVD player using an RF converter. This takes the audio and video signals from the DVD and produces a channel 3 or 4 output you tune in on your TV. Converters cost around $10 to $20 and are available at Radio Shack or retailers who sell TV's.

Feb 23, 2009 | RCA DRC277 DVD Player

1 Answer

Vcr recording


if there is a cable box hooked up to this vcr, the vcr needs to stay on channel 3 to record.the output of the vcr either hooks up to the tv from the coax out , or from one of the other possible outputs such as rca cables [red, white, yellow] to one of the tv's aux/video/line in or source inputs.
wg

Feb 05, 2008 | Televison & Video

1 Answer

Rca vcr


there a a bunch of different ways. 1) if you don't have a cable box hooked up to this tv,plug the main cable wire into the vcr input then the vcr outout to the tv.2) if you do have a cable box, plug the main cable into the cable box input, then the output to the vcr input, then the vcr output to the tv. put both the tv & vcr on channel 3 for this connection. [ you must have the vcr on channel 3 to record from the cable box!] 3) if you have aux line/video or source inputs on the back of your tv,you can hook up rca cables [ red, white,& yellow ] from the rca outputs on the vcr to the tv inputs.
hope this helps
wg

Feb 04, 2008 | RCA VR637HF VHS VCR

1 Answer

Magnavox MWR10D6 can't record from camcorder wrong channel


OK...try this...plug your RCA cables from your camcorder into the RCA input jacks on the back of the recorder. If you have a VCR, it can be plugged into the coax input on the back of the recorder. Use the coax output and plug it into a RF modulator (about $20 at Wal Mart). Plug the RCA output cables from the recorder into the RF modulator as well (Don't ask me why, but it seems to work on mine). Connect a coax cable from the RF modulator to the TV. Make sure the TV and Recorder are both on the right channel. The RF modulator will have a channel switch to use channel 3 or 4 on the TV. Make sure the recorder is set to E1 (Rear). You can check this with the channel +/- buttons on the bottom right of the remote. Good luck.

Jan 06, 2008 | Philips Magnavox MWR10D6 DVD Recorder

1 Answer

No display


Press the DVD button on the Philips remote. Make sure the yellow part of the RCA cable is plugged into Output/CVBS/Out on the back of the Philips, and that it is plugged into a yellow input of your TV. Change your TV channel to Av1, av2, video 1, video 2, aux, aux 2, or whatever the correct video channel is on your TV. Then press setup - you will get your picture.
In order for the coax connection to work on Ch. 3 of your TV, you will have to get an additional piece of equipment - an RF modulator. It's better just to stick with the RCA red, yellow, white cables.

Sep 02, 2007 | Philips DVDR3455H/37B

Not finding what you are looking for?
KLH DVD8350 DVD Player Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top KLH Televison & Video Experts

ray gallant

Level 3 Expert

68557 Answers

The Knight
The Knight

Level 3 Expert

76407 Answers

Tom Chichester

Level 3 Expert

55993 Answers

Are you a KLH Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...