Question about Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher

1 Answer

Fault with Hotpoint BCI45 Dishwasher

Hi I have an integrated slimline Hotpoint BCI45 dishwasher that was fitted by the previous homeowner. On starting a program and shuting the down the machine beeps and on opening the door the second green light from the left is flashing (regardless of which program you choose) and there is no water in the dishwasher. Hotpoint want to charge me £90 call out to look at it and won't tell me what's wrong on the phone. Any service manual would be much appreciated Cheers Gary

Posted by garyjonesUK on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 57 Answers

This a generic problem with hotpoint dishwashers..
Water is present in the flood catching tray at the bottom which usually indicates that there is a leak somewhere. More often than not this is just a pipe with a poor fitting and simply tightening the clip is enough to stop the leak. Our machine had a very slow leak from one pipe (not enough to trigger the alarm) which was fixed in this way. The leak is detected by a small float switch located in the flood catch tray.

Undo 4 screws on the metal plate under the dishwasher 3 at the front 1 at the back, this reveals The pump check the seals are in place on the waste pump.

Posted on May 23, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

No hot water or drying cycle

Possible that the main controller unit is not switching on the heater for the hot wash and also the program for spin in the final cycle is absent. it all points to a faulty program controller but ONLY with a voltage check at the inputs and outputs during the cycle will confirm the fault.
0helpful
1answer

No hot water in dishwasher cycle

If the program chosen contained the HOT WASH but there was not execution then the fault can be confirmed only if the voltage on the heaters and the hot line inlet be ,measured when the cycle advances to the next level. You will need to see if the program works in such a manner so as to switch on the heaters and also the hot valve to make it rinse the dishes with hot spray.
0helpful
1answer
0helpful
1answer

I have a hotpoint bc1450 no water coming into machine

Did the problem start directly after the washine machine was fixed ? I wonder if when the washing machine was moved back, the hose to the dishwasher has become trapped and kinked behind the washing machine. Or maybe the supply to the dishwasher is separate to the washing machine and has been turned off by mistake.
1helpful
1answer

Hotpoint BCI 450 error message not in the manual

I had this on my machine.This indicate the drain pump is broken. Probably due to a leak from the heating element pipe joint above it. You can easily replace the drain pump yourself. Costs around £30. I got mine from Curry's partmaster in the UK.
0helpful
2answers

POWER ON-PROGRAM WONT WORK

1. No power to the dishwasherMake sure there's power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced.

2. Door switch
Replace if defective.

3. Timer
Replace if defective (note: uncommon problem).

4. Selector switch
Replace if defective (note: uncommon problem).

0helpful
1answer

Flashing green light

Hi there. It looks like water is present in the flood catching tray at the bottom which usually indicates that there is a leak somewhere. More often than not this is just a pipe with a poor fitting and simply tightening the clip is enough to stop the leak. Our machine had a very slow leak from one pipe (not enough to trigger the alarm) which was fixed in this way. The leak is detected by a small float switch located in the flood catch tray.

Undo 4 screws on the metal plate under the dishwasher 3 at the front 1 at the back, this reveals The pump check the seals are in place on the waste pump.
0helpful
1answer

Neff slimline dishwasher type S5946

hi there sounds like your wash pump has burnt out
Not finding what you are looking for?
Hotpoint 18 in. BCI45 Slim-Line Built-in Dishwasher Logo

883 views

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Brad Brown

Level 3 Expert

18686 Answers

Mike

Level 3 Expert

4377 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...