Need a wiring diagram for marthion model 5kc49pno216 motor kc

Electric Motors: dayton motor, Electric motor repair Kansas ...

en.allexperts.com > Industry > Machine Tools > Electric Motors

Aug 24, 2010 - Electric motor repair Kansas City MEAR Service 816-650-4030: Tyler, it is ... i have a dayton motor with no wiring diagram. i need a wiring diagram for a dayton motor with a model # 5k961c and a reference # r67745ck733 ... 1992 Dodge Dynasty Blower Motor Wiring Diagram · 1998 Ford Escort Blower ...

wiring diagram (ideally color) for Dayton belt drive motor Model ...

www.electro-tech-online.com > ... > General Electronics Chat

Apr 29, 2012 - 9 posts - ‎3 authors
There is a sticker on motor indicating wiring, but seems only an. ... This is a motor for vented - big blade ceiling fan -- a belt driven Dayton Motor ...

DAYTON 1/4 HP Condenser Fan Motor,Permanent Split ...

https://www.grainger.com/.../DAYTON-1-4-HP-Condens...

W. W. Grainger
Rating: 3.8 - ‎6 reviews
Shop DAYTON 1/4 HP Condenser Fan Motor,Permanent Split Capacitor,1075 Nameplate RPM,208-230 ... Typical HVAC Condenser Fan Motor Wiring Diagram ...

DAYTON 1/3 HP Direct Drive Blower Motor, Permanent Split ...

https://www.grainger.com/.../DAYTON-1-3-HP-Direct-D...

W. W. Grainger

Wiring diagram should appear on side of motor.
Dayton is sold by grainger.
Contact WW Grainger with model number etc and they will send email the pdf file showing wiring.
Take photo of wiring diagram on motor label, and attach to question for best possible chance of accurate answer.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Might not need a schematic. Check the diodes and fuses in the power.

Your firing order is 1-4-2-5-3-6

1-2-3 on the left, front to rear
4-5-6 on the right, front to rear

-KC GTO Dad

Okay you are going to need 5 sets of RCA cables of 3 foot lengths. Ensure the KM-207 is adequately ventilated unless you want to burn up the KM-207. Next you will want to place the KC-207 near the KM-207 and connect the "Output to Amp" from the KC-207 to the "Input" to the KM-207. Now you may stack the KX-77CW, the DP-M97 and the KT-87 Tuner in no particular order. I tend to place them sideways so I may access them just in case I don't like how it is set up. Unless I can access them from the back. "Output" or "Play" from the DP-M207 goes into the "CD Input" in the back of the KC-207. "Output" or "Record" on the KC-207 "Tape 1" goes into the "Input or "Record" on the KX-77CW. "Output"or "Play" on the KX-77CW goes into the "Input" or "Play" on the "Tape 1" of the KC-207. "Output" on the KT-87 Tuner goes into the "Tuner Input" on the KC-207. Here is a trick to help you new stuff uses color codes such as White or Blue RCA cable ends, and Red RCA cable ends to indicate White or Blue for Left channel and Red for Right channel. Now you didn't indicate how to hookup speakers so I will not assume you are concerned about anything but using headphones for listening. I hope this has been of assistance.

Go here for a selection of manuals and diagrams:
http://www.dewaltservicenet.com/Products/DocumentView.aspx?productid=43476&typeId=10320&documentId=40207
Unfortunately the manual is not available but anything identified as a bearing or a bushing in the parts diagrams could probably use a drop or two of machine oil (3-in-1). Unless the loud noise is a screech oiling may not reduce it.

http://vintagewashburn.com/Wiring%20Diagrams/KC70%20-%20Wiring%20Diagram.pdf

Wire nut and tape the blue and red wires they are not used.

i need wiring diagram for a dayton electric motor 4mb22