RCA D52W23 52" HDTV CRT TV Logo

Related Topics:

Question about RCA D52W23 52" HDTV CRT TV

1 Answer

I think that is the tv, it is HDTV. The convergence is off, and I can't find convergence on the menu. please help!

Do all rca projection tv s have convergencen on the menu?

Posted by crazyb_otch1 on

Ad

1 Answer

Sonny Berry

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • RCA Master
  • 8,617 Answers

Yesn However if your convergence has disappeared from the menu. et me know and I will assist you its a easy repair and parts with instructions will cost about 12.00

Posted on Apr 22, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 56 inch RCA HDTV projection screen. the convergence is gone off the main menu. The TV is 4 years old. Please help.

These are the best repair kits I have used for convergence issues.

http://www.tvrepairkits.com/xcart/home.php?cat=3909

Please follow the link, buy the kit and follow the instructions they supply...


You can't go wrong.

Thank you and best of luck!~
0helpful
1answer

I can't find auto converge choice in menu of rca 52" rear projection tv.model # R 52 WH 74.

You have 3 pico fuses by your fly-back transformer. One of them blew that controls your convergence circuit. Your TV now thinks that it is a Basic CRT set with 1 tube. Find the bad fuse and replace with a 1/2 amp pico fuse, and re-solder all the pins of your fly-back transformer. Your menu should have the convergence option again.
1helpful
1answer

The convergance menue is gone. I need to adjust the convergance badly but it is no longer in the menu

You need to resolder the flyback transformer and replace fuse FL221 off pin 11 of the flyback transformer. The convergence power supply is not coming on so system control thinks a convergence circuit is not installed.
0helpful
1answer

TV RCA HD52W59 NO VIDEO

Sound like convergence supply problem (small fuse near flyback will be open.
0helpful
1answer

RCA 52" Convergence Problem

Replace the convergence power supply. You can get the ITC222A convergence power supply board at the following link under RCA circuit boards.
http://www.tvrepairworld.com/
0helpful
1answer

Rca 7302rd5 56"hdtv tv looks like a 3d moive

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
•Screen looks 3D
•Colors don't line up
•One or more colors can't be adjusted when using the convergence menu.
•Screen is bowed or warped.
•TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems


a56fe79.jpg

6d0da0b.jpg

fcabb43.pngCONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya - CLICK HERE
0helpful
1answer

RCA HDTV

go into the menu
looking for set up tab
looking for convergence tab
looking for automatic convergence. apply.
Fixed. NO? tv has a problem in the convergence area. Technican Job
0helpful
1answer

D52W20 red convergence problem

Do you see in Menu go to setup look for convergence if it is not there you have a open fuse 400ma FL231. Try This place for Parts http://servicemanuals.vstore.ca Let me know if you need anymore help.
0helpful
1answer

The convergence is way off on my projection rca tv - i lost the manual but i have set it before in a menu but caint remember how to get to it Was watching a movie, tv shut off and powered back on by...

It should be in the options menu. If not often RCA will drop the option when the convergence ICs go out and often the set will shut down. Heres alink that should be able to help you get a manual and parts if needed. If they dont have your manual leave an email and they should be able to get one quckly usually within an hour or two.
http://servicemanuals.vstore.ca/
0helpful
1answer

Showing picture in three segments

Test through MENU? explan that please. are there different colors that lead you to idea that is convergence.
Not finding what you are looking for?

99 views

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers

Cindy Wells

Level 3 Expert

6551 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...