An expert who has achieved level 2 by getting 100 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 500 times.
Re: no picture at receivers end
See section C. Windows Live
Messenger in the info below to setup the Audio & Video. Also send this to your family
and friends so they have their computer setup properly. Web Camera’s have to be
setup on the program they are to be used with.Just installing the camera on your computer does not set it up to
broadcast on messengers or Skype.
Each program has Options that have to be setup in order for
the Audio and Video to function properly. A.Skype Setup:
After downloading and installing Skype (http://www.skype.com/intl/en-gb/download/skype/windows/beta/downloading/)
set it up as follows:
Go to Tools,
then Options, and click on Audio Settings and set the Microphone
and Speakers to the computer Audio Card.
click on the Video Settings.
camera if Installed Properly will come up and show a video picture.
on the bottom of the page click on Save.
The camera and audio should function properly.Your friends and Family will now be able to
see and her to you. B.Yahoo Setup:
After downloading and installing Yahoo Messenger(http://ca.messenger.yahoo.com/download/
) set it up as follows:
on Messenger at the top left and then go down to Preferences
and then the Preference Window will come up.
click on Calling and Devices. In the Calling & Devices
on the right and set the Microphone and Speakers to the computer
Audio Card or sound device installed in the computer.
below that, go to the Test Audio section and(in blue writing) click on“Open the call setup assistant”
and follow the instructions on the left window.
after completing the Audio Setup, go to down and click on Webcam it
should BRODCSAST and you will see your picture.
Chat, click on MESSENGER and then
make necessary settings, click on APPLY, then OK.
click on MESSENGER and go to my WEBCAMready to use.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Mine did the same thing where the screen would go black for a few seconds and then the picture and sound came back. I would try (1) switch HDMI cables, (2) try a different HDMI input in the back of the receiver, (3) try different input in the back of the TV. None of these seemed to work with mine. I finally ended up running the cable box direct to the TV and only run the audio through the reciever via coax or digital. No more problems. I think the HDMI inputs in the back of the reciever have a problem continuously carrying the signal if it is the leaset bit weak.
Found the cause of the error, basically the other end is having trouble most likely poor line conditions.
##005 [ TX ] Failed G12 reception during G2 transmission.
A.Cause: Other party cannot properly receive the G12 signals due to poor
Solution: Have the other party boost their transmission level so they can
properly receive G12 signal.
B.Cause: Other party confused by echo and does not send G12.
Solution: Have the other party lower their transmission level so they
will not receive echo signals.
It will be one of the transistors that regulate the lower volatges (5V, 12V...) I ffixed mine. the heatsinking on those transistors is pathetic, and its no wonder they dont last. Mine was the 5V circuit, which also supplies the DSP board. so if you are getting a DSP NG, that could be that as well. Check Q1434 and Q1404. if one is faulty, it drags the other one down with it. Good luck.
is it pl;uged direct in wall must nbe on a nice hi end break surge proably got zapped transisters in it best to try to replace it u can try to un plug it from that outlet few min then back in anther one
see the thing is that for receiving and sending pictures from ur mobile via messaging option, for that u need to get ur mms service activated and after that get the mms setings from ur service provider. U need to ensure that tthing also that same mms service & setings should be available at othr end also.After that u will be able to send & receive mms from that particular no.