Question about InFocus Projector Lamp for IN24+, IN26+

Open Question

IN24+ orange lamp light is on with a brand new bulb. How do I reset the lamp hours when the lamp light will not project?

Posted by Anonymous on

Ad

2 Related Answers

Anonymous

  • 1 Answer

SOURCE: infocus IN24 lamp not lighting up

MAKE SURE BLUB WIRING IS THE SAME AS OLD BLUB, IN24 AND IN24+ WIRING IS DIFFERENT IN CONNECTOR.

Posted on May 06, 2009

Ad

patrick reagan

  • 269 Answers

SOURCE: replacing bulb

hold the volume up/down in ,switch unit on while holding these in for 30 secs, if that fails, flash unit with new software.

Posted on May 05, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Resetting the lamp timer on an infocus in24 projector


To reset the lamp timer on an in24 go to settings, then select Service. The option to reset lamp hours should be in this menu.

I hope this helps!


Projector Lamps Projector Bulbs Projector Parts Projector Repair Servcie

Jun 04, 2014 | InFocus Office Equipment & Supplies

1 Answer

We replaced the lamp in a tv mitsubishi wd-62327 now there is a orange flashing indicator light....now what?


if the set is now working,its just a matter of resetting the lamp-hour counter in the on-screen menus.be sure to clean any filters associated with the fan which cools the bulb,or your new lamp wont last long!
regards,steve

Jul 31, 2011 | Mitsubishi WD-62327 62" Rear Projection...

2 Answers

I had a projection bulb go out and after replacing it, i went to turn it on it clicks once, and the orange light starts blinking, then it clicks again and the light goes to red. this light does not blink...


Refer to mlapres' tips, pls. noavatar.png mlapres
  • Rank: Wiz
  • Rating: 84%, 330 Votes
What you need is to have the lamp timer reset. To do so, perform the following;

You will need two hands.

With the remote, press and hold down the "mute" button.

Simultaneously press and hold down the "enter" button on the front of the TV.

After about 5 seconds, a box will appear that shows the total number of hours on the lamp. To reset these hours, press the right arrow button on the remote. After doing so, another box will appear with a confirmation question and an icon for which button on the remote to press to reset the lamp hours.

Jan 09, 2011 | LG RU-60SZ30 60" Rear Projection...

1 Answer

I replaced my lamp bulb and everything works fine. The only problem is that the orange, replace indicator, is still on. Is there a way to reset it or something? TV and everything works great just the...


Try tv unplug,replug it back like an hour later.The tv will reset itself,back to the factory setting.It should detect the projection Lamp life are good and a new Lamp.The "LAMP" LED Light indicator,will go off.

Nov 30, 2010 | Zenith E44W46LCD 44" Rear Projection...

1 Answer

IN24 Multimedia Projector: Orange light bulb light came on....does this mean ...


if it runs for a few minutes before shutting down, it could be the lamp. check to see if the seams of the lamp that are closest to the underside of the top cover have foil tape covering the seams, if not then this has been known to cause premature shutdown.

May 17, 2010 | InFocus IN24 Multimedia Projector

1 Answer

Lamp went out, ordered new bulb and put in but TV did not come back on but the bulb light keeps flashing light orange. Sent new bulb back just in case it was faulty & ordered another 1. I just received...


Make sure lamp cover is put back in its position properly after bulb replacement.
If I have info about model and brand of your TV then I might offer better help to fix it.

Jan 15, 2010 | Televison & Video

3 Answers

Infocus IN24 lamp not lighting up


MAKE SURE BLUB WIRING IS THE SAME AS OLD BLUB, IN24 AND IN24+ WIRING IS DIFFERENT IN CONNECTOR.

Mar 20, 2009 | InFocus Projector Lamp for IN24+, IN26+

2 Answers

Z44SZ80/Z52SZ80 | DLP PROJECTION service codes


1. Press and hold the MENU button on the TV.
2. Press and hold the MENU button on the REMOTE
(Hold both until the service menu pops up)
3. Press and hold the ENTER button on the TV
4. Press and hold the MUTE button on the REMOTE
(Hold both until the LAMP LIFE HOURS appears on the screen)
5. To reset the lamp counter and turn off the orange light press select on the REMOTE.
6. Press Select again to con firm the operation.

Jul 09, 2008 | Zenith E44W46LCD 44" Rear Projection...

1 Answer

Mitsubishi dlp does not get picture


the plug the connects underneath is not connecting right you have to get at the plug and seat it correctly

Dec 08, 2007 | Mitsubishi WD-52525 52" Rear Projection...

3 Answers

No lit / projected image even with a new bulb!


Let me add...

I had one 3300MP and removed/replaced the bulb to dust off as it was overheating. There is a small metal like switch that resets the bulb replacement (physical switch - take a good look) -- This helped to reset the first time I did this, but doesn't reset the hours on the chip.

However, since this bulb was problematic for me, I have done this a couple of times and since has stopped powering the bulb now. So, thinking it was the bulb, I replaced the bulb, -- No good... So, thinking it was the projector, I bought a new/refurbished one on ebay -- tested the NEW bulb - NO GOOD. now I have TWO PROJECTORS, THREE BULBS and NOTHING THAT WORKS...

WHAT AM I DOING WRONG?

Apr 27, 2007 | Dell 3300MP Multimedia Projector

Not finding what you are looking for?
InFocus  Projector Lamp for IN24+, IN26+ Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Office Equipment & Supplies Experts

The Knight
The Knight

Level 3 Expert

76511 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

Are you an InFocus Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...