Rvc30w-2 control board

for your Thumper Mini Pro 2:

1. Contact Thumper customer support: Thumper is the manufacturer of the Mini Pro 2, so they may be able to provide you with a compatible replacement control board. When contacting Thumper, provide them with as much information as possible about the broken control board, including any part numbers or identifying markings on the board.
2. Check for compatible parts: If you're unable to order a replacement control board directly from Thumper, you can try to find a compatible part from another source. Start by identifying the specific model of the control board and any compatible part numbers. You can then search for these parts on electronics retailer websites or in local electronics stores.
3. Order from an online retailer: If you're unable to find a replacement control board locally, you may be able to order one online from an electronics retailer that ships to Vietnam. Be sure to check that the retailer ships to Vietnam and that the part is compatible with your Mini Pro 2 before placing an order.
4. Find a local repair shop: If you're not comfortable replacing the control board yourself, you can try to find a local repair shop in Vietnam that can assist you. Look for shops that specialize in electronics repair or that have experience repairing massage devices. Bring the broken Mini Pro 2 and control board with you to the repair shop so that they can diagnose the problem and order any necessary replacement parts.

When ordering replacement parts for your Thumper Mini Pro 2, be sure to double-check the compatibility of the parts before purchasing.You can check the link below if the above do not help

HP LASER PRINTERS 2, 2D, 3, 3D

1. Defective cable laser scanner to dc controller.

2. Defective laser scanner assembly.

HP LASER PRINTERS 2P, 2P+, 3P
1. Bad scanner motor.

2. bad dc controller.

HP LASER PRINTERS 3SI, 4SI, 4V
1. Faulty cable assembly.

2. Scanner motor problem.

3. Defective laser scanner assembly.

4. Defective dc controller.

HP LASER PRINTERS 4, 4+, 5
1. Faulty laser scanner cable.

2. Defective laser scanner assembly.

HP LASER PRINTERS 4L, 4P, 5P, 5L, 5SI
1. Temporary error. Scanner startup failure.

2. Improperly fitted scanning assembly.

3. Scanner cable problem.

4. Defective laser scanner assembly.

5. Defective dc controller board.

HP LASER PRINTERS 1200, 2200, 3100 FAX, 3200 FAX, 4100
1. Temporary error. scanner rotation error.

2. Replace contact image sensor.

4. Replace laser scanner.

5. Replace cables to laser scanner and engine board
HP LASER PRINTERS 1100, 2100, 4000, 4050, 8000
1. Scanner start up error
2. Replace scanner cable to the D.C. controller and back to scanner. Or replace scanner cable from engine board to scanner ***'y.
3. Replace scanner ***'y.
4. Replace the engine board.
5. Replace the D.C. controller only on the 8000.
HP LASER PRINTER 2300 ERROR 52.X
1. A temporary scanner start up error.
2. This can also be the shutter tab on the print cartridge. Replace the toner cartridge.
3. Replace the scanner ***'y.
4. Replace the engine board.
HP LASER PRINTERS 4200, 4300 ERROR 52.XX
1. Printer scanner speed error has occurred.
2. Replace laser scanner ***'y
3. Replace the D.C. controller ***'y
HP COLOR LASER PRINTER 4600, 5500 ERROR 52.XK, 52.XC, 52.XM, 52.XY
1. Error code K - No Black Color.
2. Error code C - No Cyan Color
3. Error code M - No Magenta color
4. Error code Y - No Yellow color
5. Replace laser scanner ***'y
6. Replace the D.C. controller ***'y
HP LASER PRINTERS 5000, 5100
1. Printer scanner speed error has occurred.
2. Replace laser scanner ***'y
3. Replace the D.C. controller ***'y
4. Replace cable ***'y from scanner to D.C. controller.
HP LASER PRINTERS 8100, 8150
1.Laser scanner error/start up/rotation error
2.Replace laser scanner ***'y.
3.Replace D.C. controller board.
4.Replace cable ***'y from scanner to D.C. controller
HP LASER PRINTER 4500, 4550
1. Temporary error. Laser scanner error/start up/rotation error

2. Replace laser scanner.
3. Replace D.C. controller ***'y
HP COLOR LASER PRINTERS 4600, 5500
1.Laser scanner error/start up/rotation error.
2.Take the toners out and reseat them, or replace them
3. Replace laser scanner ***'y
4. Replace D.C controller board.
HP LASER PRINTER 8500, 8550
1. Temporary error. Laser scanner error/start up/rotation error

2. Replace laser scanner motor.
3. Replace D.C. controller ***'y

HP LASER PRINTER 9000
1. Temporary laser scanner error/start up/rotation error

2. Replace laser scanner.
3. Replace upper cable guide assembly.
4. Replace DC controller.

IH power voltage abnormality or IH initial abnormality.

1. Check the AC input voltage
Check if the AC input voltage is within the specified range.
(especially when the heater becomes ON after the power is turned ON (the copier is warming up))
2. Check the thermostat
Check if the thermostat is blown.
3. Check the IH control board
(1) Check if the AC input connector on the IH control board, the LGC I/F connectors CN455 is
disconnected?
(2) Check if the fuse on the IH control board has blown.
(3) Replace the IH control board.
4. Check the LGC board
(1) Check if the connector CN332,CN334 and CN360 are disconnected.
(2) Check if the conductor pattern on the board is short- or open-circuited.
(3) Replace the LGC board.

C4801
(1) Contents Trouble type Main unit board failure
Trouble code C4801 Rank C
Detection timing MFP detects simultaneous replacement of multiple boards.
Trouble isolation -
Relevant electrical parts • SSD board (SSDB)
• Printer control board (PRCB)
(2) Procedure
Step Action Control signal Location of electrical components
1 Reinstall the old PRCB. - -
2 If the above actions do not solve the problem, contact
KM. - -
NOTE
• Do not replace the printer control board and the SSD board at the same time. The backup data is lost and image failure may be
caused.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Yellow ATC Sensor Failure,Code12
Magenta ATC Sensor Failure,Code13
Cyan ATC Sensor Failure,Code14
The ATC Sensor detects an insufficient amount of developer.

Note
If this failure reoccurs three times successively, an Engine NVRAM value is set preventing further printer use until the Clear Tech Rep Fault (see pg.6-20) is performed.

Troubleshooting Procedure
Step Actions and Questions Yes No 1 Is the problem toner and/or developer empty. Replace the toner or developer. Go to step 2. 2 Is the ATC sensor clean and free of dust, toner or any other contaminates? Go to step3. Clean the ATC sensor. 3 1.Check the ATC sensor wiring harness Yellow=P/J129
Magenta=P/J130 Cyan=P/J131
2.Is the wiring harness or the sensor defective? Replace the ATC Sensor and/or wiring harness. Go to step 4. 4 1.Remove the Rear Cover and RearShield.
2.Measure the voltage at...Yellow=P405B3 Magenta=P405B8 Cyan=P405A10
on the engine control board.
3.Is the voltage between+1 and
+3VDC? Replace the engine control board. Go to step 5. 5 1.Measure the voltage at...Yellow=P405B14 Magenta=P405B11 Cyan=P405A11
on the engine control board.
2.Is the voltage+5VDC? Replace the engine control board. Go to step 6. 6
1.Measure the voltage at...Yellow=P405B2 Magenta=P405B9 Cyan=P405A9
on the engine control board.
2.Is the voltage 0VDC? Replace the engine control board.
Go to step7.
7
1.Remove the Imaging Unit Plate cover.
2.Inspect the wiring harness between the engine control board and the developer housing assembly.
3.Is the wiring harness defective? Replace the wiring harness.
Replace the ATC Sensor.
8
Run approximately 10 pages of the solid fill full-page prints for this color to ensure the error is cleared.

Scanner initialization failed, and the copy processor
board (CPB) is not communicating
with the scanner-controller board (SCB).
1. Turn the product off, and then on.
2. Check the scanner controller board
LEDs.
3. Check the connections to the scanner
controller board.
4. Replace the scanner controller board.

1) You must test first the power supply for +5DC for I.Circuit( Including EPROM, ROM, etc)
2) Test the flexible cable between KeyPanel and display board, and clean.
3) Chechk the connector between Display Board with the lower board(Main Controller Motor)for loose connection, loose wire.
4) Test the transformer controller supplying the 12VCA, to the power supply at the Main Controller Board since this supply the +5vd to the Display Board.
Finally you must have Strong Conclusion if the problem is 1)Display Board faulty, 2) Power supply Faulty, 3) Transformer Controller Faulty 4) Main Controller Board Faulty.

For All test you must use Dvoltmeter.



sincerely.
E.CUADRA
MANAGUA, NICARAGUA.C.A

Toner Suction Fan Motor (M11) Failure:

M11 connector is on the Mechanical Control Board (PWB-A),

Also check the Power Supply Unit (PU1)

Mechanical Control Board Cover

1. Remove the Upper Rear Cover.

2. Remove the Rear Cover.

3. Remove five screws [1] and the

Mechanical Control Board Cover [2].

4. Unplug the all connectors.

5. Remove five screws [3] and the

Mechanical Control Board [4].

NOTE

? When replacing the Mechanical

Control Board, be sure to replace

the EEPROM.

? When the Mechanical Control Board

has been replaced with a new one,

check the ROM version and

upgrade the firmware to the latest

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

F11 error code indicates a communication problem. The communication between the Central control board and the Motor control board cannot be sent correctly.

Potential causes:

1. Loose connections between the motor control board and the machine control board, or at
motor

2. Machine control board failure

3. Motor control board failure

4. Motor failure

5. Door lock failure
If this answers your problem, please rate my answer.
Thanks,
David

You can't sync 2 balance boards to one wii.

I heard this is why but this isnt confirmed...
the wii can only register 4 controllers at one time... the wiifit balance board counts as 2 controllers, leaving only 2 controllers available... obviously a person would want at least one regular controller to use along with the wiifit balance board, so just using wiifit leaves only one free controller slot available...

hope this helps...