Question about Pool & Spa

2 Answers

Pacifica Marquis Hot tub serial/model number TH-Y105113 power cord from wall to hot tub

Posted by Konnie Duff on

Ad

2 Answers

Mike Tellegen

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,631 Answers

Hot tubs with a cord, need to have a GFCI as part of the cord!
they are ...
Spa GFCI Power Cord In Line 120V 15A

Posted on Apr 29, 2015

Ad

Jason Dinscore

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 38 Answers

Hopefully you've found your cord by now if not let me know and i'll point you in the right direction.

Posted on Oct 27, 2013

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want manual for Marquis spa ME-33-B-Y-082212


hot tub manuals ' guides ' Marquis - Marquis Spas

www.marquisspas.com/hot_tub/manuals.asp
Marquis has indexed our hot tub manuals and hot tub guides. ... 2010 US OwnersManual · Wish Insert · Euphoria Insert · 2010 EDHT Owners Manual. 2009.

[PDF]OWNER'S MANUAL INDEX - Marquis Spas

www.marquisspas.com/documents/2009/09MQIntlEnglishManual.pdf
Failure to use, maintain or install the spa in compliance with this owner's manual could result in ... This symbol indicates the need for separate waste collection of ...

[PDF]owner's manual - Marquis Spas


Dec 30, 2015 | Cars & Trucks

1 Answer

Washer willl not fill. some very small amount of water drips into tub. i fixed the problem once by slowly adjusting the switch. it began to fast fill when the water level switch was between water level...


sounds like a bad / stuck mix valve --- the mix valve is the plastic part that the hot/cold hoses connect to on the back of the machine,, remove the two hoses..remove the back panel and the valve is held in place by one small screw,, label wires hot/cold and remove the valve. write down the make,model and serial number of th emachine and take the valve down to your local appliance repair shop and buy a new valve and then install into the machine --- hook everything back upp and test the machine,, all should be good -- with full water flow.

c...

Feb 04, 2011 | Kenmore Washing Machines

1 Answer

The circut board was replaced everything powers up lights jets the digital display all program functions to program filtering cycle.while running operation seems normal.after aprox.from start of system to...


Do you have a model and serial number so i can spec components and a diagram?
The reset is a GFCI electrical or a high limit temperature switch?
If its a GFCI you have a leak or a short or the pump is drawing to many amps likely due to something in the impeller or plumbing restricting flow. Potentially its a shaft seal issue.
How hot is the tub when it trips? Try running it cold and see if it trips. If it doesnt and its still cold its the pump. If its hot and you set it to cold its a stuck relay or contactor or triac and therefore tripping a high limit switch.
If this is a hot tub/spa the pressure switch may be an issue. It shuts down the heat typically and keeps the pumps running.
If a reset switch of any type is tripped to many times it will continue to trip at a lower and lower value.
Just some tips, hope they help. Get back to me with some info.

Jan 20, 2011 | Home

1 Answer

I have Marquis hot tub, Leisure Series, The Spirit, Model ESLS30X, serial # 0890608. My in-laws gave it to us. It's about ten years old but still works reasonably well. The one issue is water...


If you found a solution to this problem, can you tell me what it was? I have the same thing. Its a Marquis Spririt and it just doesn't get hot enough. There must be a way to "trick" the thermostat into letting the heater run longer

Dec 10, 2010 | Heating & Cooling

1 Answer

Finding the spa manufacturer


That serial code is for the controls, not the hot tub.

Usually manufacturers will attach a plaque with the hot tub details on.... this would usually be at the front of the hot tub, either on the inside of a cabinet panel, or on the exterior.

Regards,
Ian.
http://hottub.synthasite.com

Apr 05, 2009 | Estate TEDX640JQ Electric Dryer

2 Answers

Hot tub maintenance


there will be the same amount of basic maintenance on either spa. The difference will be in water chemistry. you definitely want an ozone generator on either spa. Both are awesome Mfg of spas. they both have been around since the 1980's
Ozone will keep the water cleaner, fresher smelling and reduce the total amount of traditional chemicals used in any hot tub.
There are many other solutions for taking care of water chemistry out there without using the traditional types.
some are all natural.

Jan 02, 2009 | Waterway Spa Pump & Hot Tub Pump 1.5"...

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

john h

Level 3 Expert

23590 Answers

David Spradling
David Spradling

Level 3 Expert

11960 Answers

rogerpaul3

Level 1 Expert

62 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...