Question about Sylvania 6313CA 13 in. TV/VCR Combo

1 Answer

Wont turn on

We turned the volume down and couldnt get it back up. We turned the tv off (as a gesture to reset it) Now it wont turn back on. You can hear it click on but nothing happens. There is also a vhs tape inside the tv. HELP!!!

Posted by cokefan on

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,139 Answers

OK, it looks like a power supply problem. The click you are hearing might be the shutdown relay connected to the overcurrent circuit. This might be indicating a problem in the Hv section of the TV. To get the tape out you can restore the power supply or what you could do is to try to access the drive motor and find the load and unload gear and try to turn it to take the tape out, this has worked in the past at my shop. If you have no experience in electronics I would suggest you not trying to repair this set because of the danger involved. Take it to a qualified repair shop.

Posted on Sep 19, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My COby tv wont turn on.

I unplugged my TV for 5 minutes after 5 minutes I pressed the Power button on the side of the TV not the power button on remote for a full minute. Plugged the TV back in, pressed the power button and it turned on. Doing this essentially does a reset.
0helpful
1answer

The volume onmy Emerson TV turned down to zero. I turned it up with the buttons on the TV it turned back down to zero. The zero volume stayed on the screen.I turned the volume up withremotenoresponse.

The main system control memory IC to this TV is damaged. Replace it. If you wish to get some details; visit the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
0helpful
1answer

My tv wont turn off and is flashing colors only

YOU PUT TV IN DEMO MODE, HOLD VOLUME UP AND CH. UP AT SAME TIME PLUG TV IN WHILE HOLDING ALSO POWER BUTTON FOR 15 SECONDS. SHOULD CLEAR.
0helpful
1answer

Techwood tv volume going back down

I've got this problem these fixing only work for a sort time! Volume just turns itself down?! Anyone no the real fix?
1helpful
1answer

Our power went out, and our tv wont turn back on, is there a reset switch?

sometimes you can reset the mainboard by unplugging the set for 30minutes to 1 hour and see if it resets. If that doesn't work, you can try holdin down the channel down and volume down button on the tv itself at the same time you plug in the unit and see if that helps
1helpful
1answer

My htc surround (windows 7 phone) wont turn back on if i hold the power button on it loads up to the white htc screen and stays on i tried taking the battery out to reboot it self but that didn't wrk...

PLease do a hard reset on the phone and here is how you do it .

1. Turn the phone off. If it's frozen or unresponsive, pull then replace the battery.
2. Press and hold the Volume Up and Volume Down buttons and power the phone back on.
3. Continue to hold Volume Up and Volume Down until a factory reset screen appears.
0helpful
2answers

Volume decreases by itself

maybe defective speaker or audio output ic or shorted capacitor within audio circuit
6helpful
2answers

Small Green K on the screen

With your tv on and the green K box on your left.
*unplug your tv from the outlet
*HOLD DOWN the (Volume - and input)
*Holding down the (Volume - and input) plug tv in
Tv will power on.
Now Tap the (Volume - and Channel -)
you will go in a menu tv mode
with the "remote" hit the down in the arrow (not channel or volume)
Now hit (volume +) and the tv will get arrows ex.(/////////)
The tv will turn green "meaning it was resetted"
Unplug tv from the wall.
Wait (30 Seconds)
Turn tv back on.
Since the Tv was resetted, go through the initiative Welcome startup screen. (Pick your Language, etc..)
0helpful
1answer

Wont work when i turn volume up?

clean the volume control it could be dirty
Not finding what you are looking for?

Open Questions:

0answers

My samsung TV UN70NU6070FXZC can't turn on, the red light blink 2 times with dark screen and no sound, and this cycle repeated after about 20 seconds again and again. The Tv reboot again and again. Have to unplug power cord to stop it. Samsung Main board BN94-14106C, Power supply board BN44-01016A 1. Disconnect main board from power supply board: plug power cord, backlight on, output=13v ch1=120v ch2=80v ok. 2. Connect power board to main board disconnecting two connectors to screen, it can be turned on/off normally. No T-con board is found, is it included in the main board or side board? a. TV Standby: red light on, sound off, backlight off. on power board output=12v ch1=ch2=0v, on main board SW=0.1v PW=12vx2, HAVDD=AVDD=VGH=VGHD=0v FB_TRDY_3=0v. b. TV On: red light off, sound on, backlight on, on power board: output=13v ch1=124v ch2=82v, on main board: SW=3.3v PW=13vx2, HAVDD=AVDD=VGH=0v FB_TRDY_3=0v VGHD=0.1v. It seems that video part of the main board is not working? 3. Only connect anyone of the two screen connectors to main board connecting to power board, it can be turned on/off normally. a. TV Standby: red light on, sound off, backlight off, dark screen. on power board output=12v ch1=ch2=0v, on main board SW=0.1v PW=12vx2, HAVDD=AVDD=VGH=VGHD=0v FB_TRDY_3=0v. b. TV On: red light off, sound on, backlight on, dark screen. on power board: output=13v ch1=124v ch2=82v, on main board: SW=3.3v PW=13vx2, HAVDD=AVDD=VGH=0v FB_TRDY_3=0v VGHD=0.1v. It seems that video part of the main board is not working too? Maybe both of left-screen and right-screen be faulty? It seems not to be possible. It is same if only disconnect anyone of the four screen connectorsillustration tv . 4. Connect both of the two screen connectors to main board connecting to power board, it can't be turned on/off normally. Dark screen, red light&sound&backlight blink 2 times for 2 seconds then all off. on power board output=13-12v ch1=115-105-0v ch2=77-70-0vbacklight: lightness-a little lightness-dark, on main board SW=3.3-0.1v PW=13-12vx2, HAVDD=about 6-0v AVDD=about 10v-0v VGH=about 14v-0v VGHD=about 11-0v FB_TRDY_3=3.3v-0v It seems that video part of the main board is working now?. And then after 20 seconds the cycle repeats again and again!! I had to unplug power cord to stop it. I replaced the main board and power board, nothing changed.

See all Sylvania 6313CA 13 in. TV/VCR Combo Questions

Sylvania 6313CA 13 in. TV/VCR Combo Logo

119 views

Ask a Question

Usually answered in minutes!

Top Sylvania Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76633 Answers

Cindy Wells

Level 3 Expert

6280 Answers

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

Are you a Sylvania Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...