Question about Printronix Line Matrix P5215 Printer

5 Answers

Table Mismatch Download Again (Printronix P5215)

After I turn on the printer P5215 and passed the diagnostic pass, the message error is displayed something quickly like "AB MANUAL" and then chenged into the Permanent message "Table Mismatch Download Again". What should I do to fix up this problem?

Posted by on

  • 5 more comments 
  • muliyono Sep 14, 2007

    I have solved the table mismatch problem by flash the printer. But It's still on problem. The problem of my printronix P-5215 is "HB not installed". How could I fix it up?

  • muliyono Sep 20, 2007

    Thanks for your kindness....
    I have fixed it up....
    The problem is on the data cable that connect the mainboard to the shuttle....
    I just tight it up...
    It's OK now....

  • farzad_ab Dec 04, 2007

    hi

    i have error " tabel mismatch" on my p5212...

    but i dont have flash program.

    please help me

  • Anonymous Dec 05, 2007

    HAVE

  • MISAGH_007 Dec 05, 2007

    I'VE POWER ON AND SEE THIS ERROR MSG.

    WHAT SHOULD I DO TO SOLVE IT?

  • scorpio_man May 15, 2008

    I have a problem also (table mismatch download again but in Printronix P5209) where can i download the flash and how to install it. Thank you.

  • babaguru Feb 11, 2009

    table missmatch download again problem

×

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Hi
i have an error " tabel mismatch download again" on my printonix p1000q1
how can i solve it please help me as soon as Possible please help

Posted on Mar 29, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 34 Answers

Hello, I can get your printer running... First tell me what your original problem was before you got the Table Mismatch Download Again" error. What part did you replace? What is the flash code # you used? See my image on HB NOT INSTALLD message I have been repairing and refurbishing the P5000series Line Printers for over 6 years... If I can get a little more history on that printer... I'll have it fixed. Have a good day! LineMatrix

Posted on Sep 20, 2007

  • Toby
    Toby Mar 14, 2009

    For all future "I have same problem" post "Table Mismatch Download Again". Here is the only Solution!



    If a “Table Mismatch” is displayed, recycle power and reflash the printer. Can get “Table Mismatch” after replacing CMX Board.

    “Table Mismatch”

    Flash Upgrade Instructions Using the printer’s Parallel Port:

    1. Print a configuration on the printer prior to the download. After the flash is upgraded, the printer will be at Factory settings and you will need this printout to restore any non- default settings.

    2. The PTX flash code is on a CD you should have received with printer. Don’t have? I can email you the Flash program.

    3. Turn the printer's power off.

    4. If there is a cable connected to the printer’s serial port, disconnect it.

    5. Connect a cable from the LPT1 port on a PC that has a DOS prompt mode to the printer’s parallel port.

    6. While holding down the Online & FF(Paper Advance) keys, power up the printer. The printer will display "Waiting for Program Download".

    7. At the PC’s DOS prompt, go to the directory where the file is located C:\Temp and

    type "filename.exe -pb" where filename is the name of the file that you downloaded in step 2.

    NOTE: there is a space before the -pb

    8. The printer's display will keep you informed of the status of the download. When the download is complete, cycle the printer’s power.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Reseat shuttle power and logic cables on shuttle and main board side

Posted on Apr 04, 2015

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 80 Answers

Printer having firmware issue

Posted on Jan 02, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have solve this problom plz contect me on this no 923216283330

Posted on Jan 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My HP Pavilion Entertainment PC won't boot up but displays error code 1720 - S.M.A.R.T. Hard Drive detects imminent failure.


Replace the hdd, install your OS and copy off your date. Reinstall your programmes to recover your backups.

Nov 07, 2016 | HP Computers & Internet

1 Answer

Printer says Printhead Error 1 why can't I go pass setup?


It could be a cartridge problem, or perhaps something that can be resolved by a firmware update. I found this on Lexmark's site regarding the Pro series:
support lexmark com

Aug 01, 2014 | Lexmark Pro715 Wireless All-in-One Inkjet...

1 Answer

8560 printer shut itself down and will not true back on


The following lists the chain of events that occur when you turn on a printer. You can follow this list as one means of determining if the printer is operating correctly. The exact chain of events depends upon the last power down condition and where the printer has last determined the printhead is positioned, this is stored in non-volatile RAM. The Checklist is the primary reference for troubleshooting power-up problems.

1. Power cord is plugged in and the power switch is turned on:

2. Power supply senses AC line voltage conditions (110 VAC or 220 VAC)

and enables DC voltages. If an overload occurs, the printer turns off the high voltage DC supplies, causing a "blink" effect on the Control Panel LEDs.

3. BIST test flashes the PE LED very briefly at a fast rate until the end of the

next test.

4. The Boot loader performs CPU initialization and RAM test. It then sends

the boot loader version to the serial port.

5. Power-On Self Test (POST) initializes the Control Panel. The Control

Panel LED turns red, green, orange, and then off. The Control Panel LCD then goes black and then clear. The POST version displays on the LCD

and waits two seconds. During this time the operator can press the Back

button to bypass the remaining POST test.

6. Low level Power-On Self Test (POST) diagnostics are performed. The

Control Panel displays status messages as each sub-test is performed.

This test takes about 8 seconds. All LEDs are off during the test.

If POST diagnostics pass, the Control Panel displays the Xerox logo and turns on the green LED.

If the test detects an error, the error message displays on the LCD and the printer flashes the LEDs with a repeating error code pattern.

7. The VxWorks operating system is initialized and engine code is started.

This takes about 15 seconds. The Xerox logo is displayed.

8. Print Engine Self Test (PEST) diagnostics are then performed. These test

the heaters, clutches, motors and solenoids. As each clutch is tested, you hear clicking with four high tones as each motor is tested. This test takes about 30 seconds.

9. The printer now runs the mechanical initialization. The exact sequence
depends on the initial position of the printhead and wiper assembly.

Feb 28, 2014 | Xerox Phaser 8560MFP Laser Printer

1 Answer

8560 shut down and will not turn back on


The following lists the chain of events that occur when you turn on a printer.

You can follow this list as one means of determining if the printer is operating correctly. The exact chain of events depends upon the last power down condition and where the printer has last determined the printhead is positioned, this is stored in non-volatile RAM.


1. Power cord is plugged in and the power switch is turned on:

2. Power supply senses AC line voltage conditions (110 VAC or 220 VAC)

and enables DC voltages. If an overload occurs, the printer turns off the high voltage DC supplies, causing a "blink" effect on the Control Panel LEDs.

3. BIST test flashes the PE LED very briefly at a fast rate until the end of the

next test.

4. The Boot loader performs CPU initialization and RAM test. It then sends

the boot loader version to the serial port.

5. Power-On Self Test (POST) initializes the Control Panel. The Control

Panel LED turns red, green, orange, and then off. The Control Panel LCD then goes black and then clear. The POST version displays on the LCD and waits two seconds.

During this time the operator can press the Back button to bypass the remaining POST test.




6. Low level Power-On Self Test (POST) diagnostics are performed. The



Control Panel displays status messages as each sub-test is performed. This test takes about 8 seconds. All LEDs are off during the test. If POST diagnostics pass, the Control Panel displays the Xerox logo and turns on the green LED.

If the test detects an error, the error message displays on the LCD and the printer flashes the LEDs with a repeating error code pattern.

7. The VxWorks operating system is initialized and engine code is started.

This takes about 15 seconds. The Xerox logo is displayed.

8. Print Engine Self Test (PEST) diagnostics are then performed. These test

the heaters, clutches, motors and solenoids. As each clutch is tested, you hear clicking with four high tones as each motor is tested. This test takes about 30 seconds.




Feb 28, 2014 | Xerox Phaser 8560MFP Laser Printer

1 Answer

P5215 firmware download


The firmware for this printer is not available for download via the web as there are hundreds of different types. If you detail the reason you need it (ie error code) I may be able to help.

Jun 28, 2012 | Printronix Line Matrix P5215 Printer

1 Answer

Printer Error message : Printer Error has occurred. 6000


Error 6000 gets displayed when there is a paper jam or other general malfunction. When the message "6000 Printer error has occurred. Turn off the printer then back on again. If the problem persists, see the manual." Is displayed, something may block the paper feed tray from opening.
If the printer is surrounded with documents or when you copy large documents such as books, make sure that you secure the clear space in front of the tray before printing / copying. When the error message above is displayed and if you find something is in front of the tray, remove it. Then, turn OFF the printer and back ON again and the printer will be ready for printing.
If you still have the trouble, contact the repair service.

Check the printer for any paper jam or try to reset the printer to release memory code errors.

1. Press and hold the Resume button for 1 - 2 minutes.
2. Open the cover.
3. Remove the cartridge and then reinstall it.
4. Close the cover.
5. Turn Off the printer.
6. Turn On the printer.


I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Dec 21, 2010 | Canon Office Equipment & Supplies

1 Answer

Received message "table mismatch" and priinter


There is nothing to do but try to reflash the printer firmware. If that is not successful then the cmx bd. must be replaced and reflash.

Nov 13, 2010 | Printronix P5000 Printer

1 Answer

I need the flash program for Printronix P5215. Can you please email the flash program? email:[email protected]


The flash program is also known as a driver I do believe
Here is that program in the link posted below


http://www.howtodrivers.com/model536551.html

This other link below here is the MANUAL for your printer to keep on hand in your computer if needed. It takes a few minutes to download for it is large in size.

http://www.scribd.com/doc/16855649/Printronix-P5000-Line-Matrix-Printers-Maintenance-Manual

Jul 18, 2010 | Printronix Line Matrix P5215 Printer

Not finding what you are looking for?
Printronix Line Matrix P5215 Printer Logo

2,509 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printronix Office Equipment & Supplies Experts

Chinmay Joshi
Chinmay Joshi

Level 2 Expert

148 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Are you a Printronix Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...