Zebra P330i Thermal Card Printer Logo

Related Topics:

Question about Zebra P330i Thermal Card Printer

2 Answers

Not pulling the cards

My printer does not pull the cards, it just doesn't roll to pull it and it makes a horrible noise while trying to do so. I've already changed the thickness but it doesn't work. What can it be?

Posted by blue velvet on

Ad

2 Answers

Paulo Rangel

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Zebra Expert
  • 285 Answers

Try to ajust the printer to the correct cards (blue arrows at the front. you possible using the tick seting to use tin cards.

Posted on May 05, 2008

Ad

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 77 Answers

Have you replaced your sticky roller and is it seated correctly?

Posted on Feb 01, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Dyson dc17 makes loud noise on carpet setting. It's like a high pitch ringing almost but won't make the noise on hard floor, only carpet setting. Ive checked for blockages and cleaned all parts but makes...

It is probably the brush roll motor making the noise. Remove the brush roll & belt and turn both motors on. If you do not hear the noise when both motors are running the noise is likely coming from the brush roll
1helpful
1answer

My husband ran over my daughters shirt with our Dyson DC17 animal. Now it's making this horrible load ratting noise. I've taken the head off. Clean the beater bar. The belt is in tact. No

First make sure there are not any of the rubber cogs missing from the belt, it may be wise to replace the belt anyway because the cogs may be worn. Make sure the brush roll does not have any play in it anywhere and that It fits tightly in the nozzle housing without any play. If there is any play or wiggle that will cause it to move.
0helpful
1answer

917.00 transfer roll

The cuase is the HVPS card. Clean it or replace it.
0helpful
1answer

Cd in macbook wont ejec

This can be a problem. First try rebooting the machine, and holding the eject button when you hear the startup tone. Hopefully, that will force-eject it.
If that doesn't work, you'll need to get creative. Get a playing card or something similar, and put some rolled-over tape on one side close to the edge, so there's a sticky side out. Turn the computer off, and try to get the playing card into the CD drive, with the tape making contact with the stuck CD. Reboot, holding the eject button when you hear the eject button again, and pulling the card out. Hopefully, the CD will come out with the card. If it doesn't work, just keep trying, and you'll get it out eventually.
Generally what causes this is keeping CDs in the computer for an extended period of time, especially while the computer is powered off. Make sure you remove all CDs before moving or turning off your computer.
0helpful
1answer

After about 2 weeks of use, the microwave began to make a horrible buzzing noise from the "box" in the upper right hand corner on the back. It also smelled horrible. It then proceeded to stop working...

Two weeks? This is a warranty problem. The buzzing noise was probably either from high-voltage arcing or an overloaded transformer trying to drive a shorted component. The smell is from something electrical getting fried. Remember it; the next time you smell it, you'll know to pull the plug.
0helpful
1answer

Makes a horrible noise

The printer gears are fail, find a canon service center
0helpful
1answer

Horrible grinding noise

The problem sounds like a broken or stripped gear in the printer. If the unit is under warranty I would contact the authorized repair station for that printer in your local area.
0helpful
1answer

Problem

this happened to me and cost me £1 to get a fix from ebay. so here it is for free. The ink pad under where the printer head parks is full.Turn the printer on. Hold the stop maintenance and power buttons down for about 10 seconds. You will hear a horrible grinding noise. PULL OUT THE MAINS CABLE. Turn the printer back on and pull the mains cable out when the head moves to the left. Use kitchen roll to soak up lots of the ink. Use kitchen roll to soak up the ink about once a month. Worked for me for over a year now
STEVE
0helpful
1answer

Won't pick up the paper but the cartridges move up and down the line

Hai Boss it is not the problem with the Catridge . Some of the Spring has begin missing in assemble part . you pull the paper out the problem cause from there never ever pull the paper ..
Not finding what you are looking for?

294 views

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

David Shaub

Level 3 Expert

2994 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Ekse

Level 3 Expert

13435 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...