Question about Protron PLTV-32 Television

1 Answer

Audio on the low end is not linear

Turning the volume down to the last mark of very quiet, the 2nd mark the volume jumps, not real loud, but not what the next level of quiet should be. It has been this way since new, just really bugging us now. Is there any kind of software refresh in this TV?

Posted by BrooksFamily on

  • 1 more comment 
  • BrooksFamily Sep 15, 2007

    This is not an issue with boot up (turn on) I don't believe. I am talking about, with the TV on and then from a moderate volume, turn it down. Say the phone rings and you want to lower the volume so folks in the room would still be able to hear but not interfer with my call. The last mark (lowest volume setting) before the sound is off, is too low to hear and the next mark borders on too loud to talk on the phone or sleep. It is that transistion that is my problem.

    Now if you still suggest it is a control board issue, where can such a replacement be ordered by a handyman for this line and model?

    Thanks again...let's try it from here.

  • BrooksFamily Oct 02, 2007

    I didn't see a reply to my Comment by BrooksFamily, posted on Sep 15, 2007, I am still awaiting a reply to see if I was clear in my description. Thanks

  • BrooksFamily Oct 07, 2007

    I would really appreciate if someone else would review this thread to see if additional assistance can be suggested.

×

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 317 Answers

Your tv has a defective control board. it's not reading the software at boot up..john

Posted on Sep 12, 2007

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to change the volume on my naxa nx 144 mp3 player

You can change the volume of your naxa nx 144 video player by;
1.Pressing and then holding down the VOL Button for about four to five seconds
2.After you do that you will see the number near the center of the bottom of the screen on the player's screen start to blink or flash.
3.When it is still flashing press the |<< O >>| or what some people including myself call the Rewind or Fast Forward buttons until the number that is still flashing on the bottom of the screen is a diffirent number then when it was when it started flashing earlier.
4. After you change the still flashing number for the player's volume until you get it as loud or as quiet as you desire repeat the first step by holding down the VOL Button once again for about four or five seconds and....v`iola it should be adjusted to your liking now.

Oh yeah before I forget here is a friendly word of advice for you. DO NOT FORGET and leave the volume on real loud and then play your song,video or,ect. before turning you volume back down because it will be REALLY LOUD and REALLY PAINFUL ON YOU EARS.
Thank You and I hope this helps for you.
7helpful
2answers

Kenwood TS50 - Max volume gives very low audio while receiving

It sound like a bad reostat in the volume control. if its under warranty send unit back to kenwood and have them replace the volume control, and possible speaker involvement.
0helpful
1answer

Extreme distortion/static in music.

you might have blown your speakers. Thats what it sounds like, if it got loud with a lot of low-end then it got all staticy and distorted, you fried teh speakers.
0helpful
1answer

CB radio PA speaker

Freddy, hello. The first thought that comes to mind with your problem is that if the 29 is an older model, the audio circuit or audio chip could be tired. If your talking about the receive volume being low thru the ext. speaker, then there is a rx. wire inside the mic cord. When it breaks, it cuts the volume in about half. The rx. wire is on pin # 4. Maybe your using the wrong ohm value speaker. You need 4 or 8 ohm. If you are refering to the outgoing modulation being real low, then the radio mod. has just been turned down to 50-60%. That's about all I've got for now, not being able to actuallly see the radio,,, Have a good day, and let me know how it goes,, Mechanic
10helpful
4answers

RCA Wireless headphone triggers off after 35 seconds of operation

ya the volume of your source is your issue.
if it is too low, the unit cuts out after 45 seconds or so...
crank up the volume and turn it down on your headset
0helpful
1answer

Alpine CDA-9857 Volume Fluctuations

Please see my solution posted on Mar 13. No other brain waves yet!
0helpful
1answer

The Output Volume Is Extremely Low!

Sometimes the rear channels can be used as a 2nd zone. Does the unit have A&B speaker selection on front panel? Usually if it has a 2nd zone it will say in owerns manual or on back of unit or on front panel as well. That is when you have the option to adjust the volume in the menu on the 2nd zone. GURU JAY
48helpful
11answers

Low volume

> Open Control Panel
> Sound Properties
> Speaker Properties
> Enhancements
>

Loudness Equalization : on

Equalizer: Choose one (Jazz seems to be loudest setting but sounds of hallway effect so I use powerful for clarity.)

This has more than doubled the level of volume on my acer 5570.

- verc
Not finding what you are looking for?
Protron PLTV-32 Television Logo

Related Topics:

57 views

Ask a Question

Usually answered in minutes!

Top Protron Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76633 Answers

Cindy Wells

Level 3 Expert

6281 Answers

Jayesh Panchal
Jayesh Panchal

Level 2 Expert

280 Answers

Are you a Protron Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...