Question about Pioneer SD-P50A5-K 50" Rear Projection Television

TV trouble My Tv shutoff by it self. I can unplug it and plug it right back up and it comes on. After 10 to 15 min. it shuts off again.

prov1x Dec 28, 2008

is there a place i can send this to get is fixed?

4 Answers

Anonymous

On mine the Convergence board goes bad every 3 to 5 years at a cost of approx. $400.00 to replace each time.

Posted on Oct 13, 2008

Anonymous

Level 1:

An expert who has achieved level 1.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.

Problem Solver:

An expert who has answered 5 questions.
Contributor
13 Answers

You may need the power supply board resoldered as I had the same problem. The guy listed below can do it for you as I shipped mine from Illinois to him in California... Piece of cake getting the board out of the back and it's not too fraigile... Just pack in bubble wrap and it will be fine. My TV is now working great.

BUT DON'T DELAY AS SOONER LATER TV WILL NOT RESTART..

http://www.avsforum.com/avs-vb/showthread.php?t=402397&pp=30&page=38

Good luck.

cell

Posted on Jan 16, 2008

Vista Electronics

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.
Master
1,694 Answers

Practice visual acuity technique.Solder any/all bad connects.Check horiz.driver cap(s) located near small driver Xformer.Remember, above all else,DO NO HARM!

Posted on Sep 24, 2007

Vista Electronics Dec 09, 2007

Remove original solder from 5v regulators on power supply circuit board, clean and re-solder.....re-assemble...................T.

Lashawn Robinson

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Genius:

An expert who has answered 1,000 questions.
Master
1,153 Answers

Check power supply for loose connection under board. Also check large caps in power supply

Posted on Sep 10, 2007

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

I have a 73 inch Mitsubishi wd-73c9 that I recently changed the dlp chip and the board it attaches to because of white dots now my TV comes on looks great and shuts off after a few min I can turn it right...

Hello, go through all the plugs especially the fan plugs and make sure that the fans are running.....tks

Jan 26, 2015 | Mitsubishi Televison & Video

1 Answer

How to take it off the timer

cut off the tv unplug it and plug it in after a few mins if the timer screen comes back again have a tech look on your tv,the problem is the eprom that needs to be unsolder out of the set and solder it back so it can reset it self.

Aug 30, 2012 | Sanyo Televison & Video

1 Answer

Rca 32in TV Product serial#f483ceok5 RCA 32in

try unplugging the tv from all imputs and power and let set over night then plug everything back in.

Feb 10, 2011 | RCA TruFlat 27F520T 27" TV

1 Answer

1 vertical line across the screen maybe 1" tall. It appears to have the entire picture in that short little space.

tv turns its self off i unplug it plug it back in it will flash on not showing picture it u can her it flash on and right back of some times it will not flash in back of tv and i can hit power it will flash and go off every now and then it will come on show picture after being unplugged and plugged back but then shuts off

Jul 16, 2010 | Toshiba 36A50 36" TV

1 Answer

Self clean lock

Hello there:
Normally every body gets this almost right by cutting the power but there is a trick to this it can be done in 2 different ways depending on the unit
First unplug the unit and wait 15 -30 seconds then plug it back in and wait for 15 to 30 seconds then unplug it again and repeat this step 1 more time then upon the final plug in wait for 5 min and then unlock as you normally would.
now on the newer units the trick is to let it stand unplugged for 1 hour to allow the internal reset device to reset the appliance then plug it back in and then wait 5 min and you should hear it automatically unlock the appliance or you cn simply unlock it as you normally would
BUT REMEMBER DO NOT TOUCH IT FOR THE 5 MINUTES AFTER THE PLUG IN STAGE OR YOU WILL HAVE TO DO IT ALL OVER AGAIN OK
Hope this is very helpful for you please keep me posted on how this is going there is still more that i can show you but i wanted to start with the basics ok?
Best regards Michael

Apr 28, 2010 | Frigidaire 30" Self-Cleaning Freestanding...

1 Answer

Modle# PT53WX54J it shuts off by it self after 20 min of use.I have to unplug it then plug it back in to get to turn back on. then it shuts off again after 20 min.

How many flashes?

Oct 04, 2009 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

Tv coms on a few mun. then shuts down

Rear projection televisions are old technology. It is probably overheating. Check the cooling fans.

Time to upgrade to a Ultra HD 4K Flatscreen.

Mar 07, 2018 | Pioneer SD-P50A3Q 50" Rear Projection...

0 Answers

Sharp lc-c3234u 32" flat screen hdtv turns off and on

Jul 28, 2008 | Sharp Aquos LC-42D62U 42 in. LCD HDTV

3 Answers

TV suddenly shuts off and lamp light comes on, but lamp is OK

did you reset the lamp timer? just a guess

Feb 07, 2008 | Mitsubishi WD-62827 62" Television

3 Answers

Lcd tv shuts down by its self

All you need to do is remove the back cover, then remove the metal cover that covered the power supply. Watch tv w/o cover, it won't shut down again. Try it and post here if it works.

Sep 12, 2007 | Televison & Video