Question about Siemens SpeedStream Modem (4100) (SS4100)

1 Answer

Printer and Modem

When I use the printer, the SpeedStream disconnects and I have to reset it. It worked for a year. I checked the connections. Pulled out all cords and reinserted them. Could it be the electricity in the den---looks like I get a surge on the computer screen---it dims and then brightens.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Are you using a USB cable to connect your modem ? Are you using a USB cable to connect your printer ? If you are using a USB cable to connect your modem, try using an ethernet cable and your LAN card instead. It will work better and you won't need modem drivers to make it work. You do however have to have a LAN card or built-in LAN adapter. As long as you have one of those 2, the best way to hook up your modem would be by using the ethernet jack on the modem straight into your LAN card/adapter. If you are not using USB to connect your modem then please send me your printer model and how it's hooked up and I will help you figure it out. Hope this helps.

Posted on Sep 27, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speedstream ss2624 firmware update


Reset your router . Disconnect the power cord by 40 seconds, and after inmediately click in the small switch that router has with a pencil eraser, for to reset, try again.
However after that if the wireless is o.k good, but if not open the open network connection, select the network troubleshooting and fix it.
You must be sure that connection to Internet BY YOUR supplier is GOOD, and NOT has problem.
God bless you

Jul 28, 2013 | Computers & Internet

1 Answer

HP F4140 Printer - all lights flashing, blinking E


This is a printer hardware error, you cant try below reset methods.
Power Drain:1. Unplug the printer power cord from wall and the printer, disconnect USB cable from printer.2. Press and hold the power "ON/OFF" button for 30 seconds and release it.3. Connected the power and check the printer.

Dec 08, 2011 | HP DeskJet 6988 Printer

1 Answer

The electricity went off to my printer and it hasn't worked since. I have tried turning it on and off. I have tried resetting the ing cartriges . I have tried unplugging , waiting and replugging. Nothing...


Which brand/model of printer do you have? Check the warranty for the printer and contacting the manufacturer, if it is under warranty.

First though what type of power cord does the printer have? If there is a power module (brick), disconnect the cord from both the printer, the wall outlet and separate the cord from the module. Wait a minute and then plug the cord into the module and then into the wall outlet. If it has an LED, is that LED lit? (Check the printer itself or the module and find out what power should be getting to the printer. If you have a multi-meter, check if the cord is getting the correct power level.) Try another power cord if you have one that matches the connection and the voltage output (for a power module).

Some printers have a soldered-in fuse and it should be handled as a warranty repair when the printer is under a year old.

I hope this helps.

Cindy Wells
(I'm currently waiting for a return shipping label for a similar printer issue. HP gave a credit for a new printer instead of sending a refurbished unit. I didn't have a spare power cord but did have 30 V at the printer side of the power module's cord. This was at the specifications for the unit. This is the first HP printer I've ever had fail within a year. Previously the ink jet failed after 9 years of use.)

Apr 02, 2011 | Office Equipment & Supplies

1 Answer

Fax will not work at all. I have reloaded the software, unplugged and replugged everything, talked with HP(they want a fee to talk) When you turn it on, it is a "fax failure" message. Will not send or...


Try to Run Fax Test
Press the Setup button on front panel
Scroll to Tools - Press OK
Choose Run Fax Test - Press OK
It should print the Fax Test Report.. it will list you the possible cause why you are getting Fax Failure..

If it says Hardware Test Failed..do a Reset on the Printer ( Hard Reset )

this will printer reset the settings to Factory default like your rings to answer will change to default, Speed Dial list will be wiped off

Steps to do :
Disconnect the Phone cord from EXT 1 of printer

while the printer is on, Disconnect the power cord from back of printer. While holding the # and 6 Buttons, connect the cord back and release the buttons after 5-6 seconds..

go thru the alignment process and re-align the printer
Connect the Phone cord back and try to Run the Fax Test and check if everything passes in the list.

Jun 25, 2010 | HP OfficeJet 6310 All-in-One Printer...

1 Answer

I keep getting error message ink system failure. Everything I tried does not work. It is only 1 year old. What else can I try?


Have you tried cleaning the Cartridges contact points ( electrical contacts )
Try doing a reset on printer

Disconnect power cord from back of printer ( while printer has power ), hold the power button on printer and connect it back

If this does not fix the issue, you may need to replace the cartriges

Jun 19, 2010 | HP Officejet 6500 Wireless All-in-One...

1 Answer

F340 printer


Hi Pear,

I'm sure that this is an Hardware issue, this could be fixed by resetting the printer.

Step 1: [Power Drain]

>>Turn off the printer by disconnecting the power cord from the back and also disconnect the power cord from the wall outlet

>>Then Press and hold the ON button for 30 seconds.

>>Connect the power cord, if it did not work go to step 2.

Step 2: [ NVM Reset]

>>Take out the Ink Cartridges out.

>>While the printer is on, unhook the power cable from the back of the printer.

>>Press and hold CANCEL and PLAIN PAPER button simultaneously, while holding these two button insert the power cable and keep holding for 10-20 seconds.

>>Release the button and check the printer.

>>If the problem exist, service or replace the printer by calling HP.

Thanks
Rizwan
[email protected]

Jan 02, 2009 | HP Deskjet F340 All-In-One Printer

2 Answers

My printer won't turn on after a power failure.


No, there is no reset button.
disconnect the pirnter from the computer and the power cord. press and hold the power button for 30sec. connect the power cord, and connect it back to the computer.

Dec 01, 2008 | HP Photosmart C3180 All-In-One InkJet...

1 Answer

Carriage jam


SolutionStep one: Perform a power reset and connect the printer directly into the electrical outlet Remove all the paper loaded in the main input tray.
Make sure that the product is turned off. 
Disconnect the USB cable from the back of the product.
Disconnect the power cord from the product.
Disconnect the power cord from the electrical outlet and wait 10 seconds.
Reconnect the power cord directly into the electrical outlet and check for the following.
Make sure that the power cord used is the one provided with the product.
If a computer is connected to the product, make sure that the computer is connected to a grounded (three-prong) wall outlet.
Make sure that the power cord is firmly connected to both the product and the power supply.
Reconnect the power cord to the back of the product.
Press the power button ( ) to turn on the product.
Reconnect the USB cable to the back of the product.
If the issue is resolved, proceed to Step six: Print a self-test page.
If the issue continues, proceed to the next step.

for more information please go to below link>>

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01458822&cc=us&lc=en&dlc=en

Thanks for using FixYa.

Nov 11, 2008 | HP Photosmart C4280 Aio Printer

1 Answer

Carriage jam error message


SolutionStep one: Perform a power reset and connect the printer directly into the electrical outlet Remove all the paper loaded in the main input tray.Make sure that the product is turned off. 
Disconnect the USB cable from the back of the product.
Disconnect the power cord from the product.
Disconnect the power cord from the electrical outlet and wait 10 seconds.
Reconnect the power cord directly into the electrical outlet and check for the following.
Make sure that the power cord used is the one provided with the product.
If a computer is connected to the product, make sure that the computer is connected to a grounded (three-prong) wall outlet.
Make sure that the power cord is firmly connected to both the product and the power supply.
Reconnect the power cord to the back of the product.
Press the power button ( ) to turn on the product.
Reconnect the USB cable to the back of the product.
If the issue is resolved, proceed to Step six: Print a self-test page.
If the issue continues, proceed to the next step.

for more information please go to below link>>

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01458822&cc=us&lc=en&dlc=en

Thanks for using FixYa.

Nov 06, 2007 | HP PSC 2410 All-In-One InkJet Printer

Not finding what you are looking for?
Siemens SpeedStream Modem (4100) (SS4100) Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Prashant M
Prashant M

Level 3 Expert

2277 Answers

john smith

Level 2 Expert

406 Answers

Are you a Siemens Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...