Outside screen cracked

for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

http://www.youtube.com/watch?v=CRw03PpRJfs

http://www.youtube.com/watch?v=mlpgiR1fRmo
longer video

Dear Sir:

Turn off the power to your computer and unplug all cables connected to it. Remove the battery, if one is installed.

2

Locate the covered screws around the cracked screen. Remove the rubber or plastic covers, then unscrew the screws.

3

Gently remove the plastic frame around the cracked screen and set it aside. Disconnect any power cords or cables going into the LCD screen.

4

Remove the cracked screen and slide the new screen into place. Replace any tape or plastic fasteners that hold it in place.

5

Reconnect all internal cords to the screen. Screw in the frame and replace all the screw covers.

6

Reconnect the power supply and all external cables to the LCD screen and switch it on.

sincerely. God bless you

ernesto cuadra

managua, nicaragua. c.a.

pop the rear deck lid and remove the right rear plastic trunk cover. To do this you will remove the small plastic piece that is directly in front of the right rear tail light. Then remove the big plastic screw that retains the center plastic deck lid cover. Now remove the three 10mm nuts that keep the right rear plastic cover secured. Remove the right rear plastic cover. Be careful as it can crack if you put too much pressure on it. Look inside and to the right rear where the antenna mast comes up. You will see a small 10mm nut that holds the antenna mast to the body. Take that nut off. This will release the outer body cover from the inner cover. Remove the outer body cover and then remove the two screws from the OUTSIDE of the body cover. Now follow the antenna body down and you will see two or three additional small nuts that hold the antenna assembly metal bracket in place. Remove these. Unplug the antenna co-ax cable from the input. It just slides out. Unplug the antenna connection as well. This is the jack that has the power wires. You will also need to unscrew the ground wire from the inner body frame. There might be a nut on top of the actual antenna mast. If so, just unscrew it. The entire antenna assembly will now lift out. It's a mildly tight fit but you don't need to be too gentle in this step. Normally the problem is the antenna belt has broken inside the antenna assembly and there is no hope of replacing that belt. You have to replace the entire assembly. I found mine on Craigslist from a guy parting his totaled Z. May it rest in peace. His loss - my gain! Typical price is $65, maybe you can talk him down to $50. Installation is the above process in reverse.

Hi

Click here to know how to replace and also to know more about the replacement instructions.

Regards,

Saleem

Your LCD/monitor is cracked from the inside. There are several things that can cause a screen to crack from the inside. The two most common are pressure on the screen or dropping the machine. Sorry, but it is irreparable. You need to buy a replacement.

you can use warranty or send it to the company and they will charge you if you hadnt taooken the warranty

The outside part that you can touch is just a plastic cover to protect the screen. The inside is actually where the lcd screen is. If the screen looks cracked then it most likely is. Its gonna be $89 to send your psp in to sony, call 1-800-345-7669 if thats what you wanna do.

The LCD screens are built with a over-cover of a plastic film and the LCD is inside the cover. Any damage on the LCD glass will not be felt physically on the outside of the screen. So, chances are your LCD is cracked if you find a spider web or a liquid spill effect visible.

No. Needs to be replace...