My nokia 6500 slide is not detected on my p3 processor computer

There are lot of ways to Unlock the Phone from Network lock,But i suggest the Network Unlock code to unlock the Phone from Network ,you can get the unlock code at here
Mobile-Unlocker and follow the instructions below and unlock it step by step.....


1 - Switch on your Nokia 6500 SLIDE without any sim card.
2 - Don't bother as to what is displayed on your Nokia 6500 SLIDE.
3 - Compose #pw+CODE+1#.
4 - The Nokia 6500 SLIDE would then display the message "SIM Restriction Off" and will be unlocked!


Unlocking instructions for Nokia 6500 SLIDE:


Note :For Nokia 6500 SLIDE mobile phones locked to the network Fido or Rogers in Canada follow these instructions :
1 - Switch on your Nokia 6500 SLIDE without any sim card.
2 - Don't bother as to what is displayed on your Nokia 6500 SLIDE.
3 - Compose #pw+CODE+7#.
4 - The Nokia 6500 SLIDE would then display the message "SIM Restriction Off" and will be unlocked!

The letter p appears if you press the button star(*) three times quickly
The letter w appears if you press the button star(*) four times quickly
The symbol + appears if you press the button star(*) two times quickly
The CODE you need to enter is the unique unlock code for your Nokia 6500 SLIDE

1) Make sure that your Power Source is giving enough energy to the new Mother Board and make sure it's compatible.
2) Make sure that the new Mother Board is compatible with all of your current hardware, you can check this in the webpage from the Mother Board Company.
3) Check the voltage requirements for the Mother Board, check the BUS speed of the Mother Board and compatibility with the transfer speed of each of your current hardware.
4) It's never recommended yo change only a Mother Board since usually there's going to be problems with the rest of the hardware if it wasn't changed, if the problem persists, you'll have to buy new hardware that is compatible with your new Mother Board.
5) If you know how a BIOS works and how to configure one, you could also check the configuration in the BIOS, not sure it will work but it's worth a try if you know what you're doing.

1. Your hard external hard drive may not be supported by the mother board.
It may be to large for the PC to detect.
check *********** board manual to see if the hard drive is compatible with the PC.
2. Check the USB connection with another USB drive to see if it is detected > if so then the 1TB drive may not be compatible with *********** board.

IBM 09k9982 011 ATX MOTHERBOARD P3 11s19k5609z 1N0Z9131W3C Netvista Socket 370
Condition: Used - pulled - working
Content: 1 Motherboard only
Compatible part # 06P2525 01
FRU 09K9982 , 89P8010
Chipset Intel 815 - FSB 100/133 - 2x Dimm PC100/PC133 - Agp 4x - 3 PCI - 2 USB
IBM 09K9982 Netvista Pentium III Moederbord.
Socket 370 Mini-ATX.
Intel 815 chipset.
2x Dimm pc-100/pc-133
Agp-slot (4x)
3x PCI
2x USB
Sound and Video on-board.

To use with : FOR IBM Netvista Socket 370 , 6648-TAU

hope this helps

Hello, Please use this pc suite then: www.nokia.co.id/dukungan/software/nokia-pc-suites/compatibility-and-download www.brothersoft.com/nokia-pc-suite-66393.html

Regards

THE SE440BX2 MOTHER BOARD CAN SUPPORT P3,P2 PROCESSORS(P3 850 MHZ)....,BUT NOT P4 AND HIGHER VERSIONS...THIS MOTHER BOARD SUPPORTS UPTO 768 MB OF RAM,NOT MORE THAN THIS...

You might have damaged the CPU/ motherboard during the process of overclocking.

Check your CPU on other compatible mobo.

Check your mobo documentation properly & set the jumpers rightly. If that doesn't help, you will have to replace the mobo.

The main thing is to find out what type the processor socket is.
Then buy a board with the same socket, and that can take the same ram type. This is your board so any equivelent should be fine.

CPU

1. Socket 754 for AMD Athlon64

Chipset

1. SiS 760 Chipset
2. SiS 964 Chipset
3. Super I/O: ITE IT8705 chip
4. Integrated peripherals
   1. Realtek 8100C Ethernet controller
   2. Realtek ALC655 Audio AC'97 Codec
5. Local Frame Buffer memory 64 MB

Memory

1. Type: DDR400/ 333/ 266- 184pin
2. Max capacity: Up to 2GB by 2 DIMM slots

Internal I/O Connectors

1. 2 x Serial ATA connector
2. 2 x UDMA ATA 133/100/66 Bus Master IDE connectors
3. 1 x FDD connector
4. 2 x USB 2.0/1.1 connectors (supports 4 ports)
5. S/P DIF input/output pin header
6. 2 x cooling fan pin headers
7. CD/AUX in
8. 1 x Game/Midi connector
9. 1 x COM connector

Expansion Slots

1. 1 x AGP slot (8x/4x-AGP 3.0 compliant), supports 1.5v display card only.
2. 3 x PCI slots (PCI 2.2 compliant)

Back Panel Connectors

1. PS/2 Keyboard / Mouse
2. 4 x USB 2.0/1.1 ports
3. 1 x VGA port
4. 1 x RJ45 port
5. 1 x COM ports
6. 1 x LPT
7. Audio (1 x Line-in / 1 x Line-out / 1 x Mic) connector

CPU/AGP/DIMM setting

1. CPU FSB adjustable via BIOS

Power

1. ATX power connector and ATX 12V connector
2. Power-off by Windows 98/ Me/ 2000/ XP shut down and switch

Form Factor

1. Micro ATX form factor
2. 24.4 x 24.4 cm

H/W Monitoring

1. System health status auto-detect and report by BIOS
2. Hardware detecting and reporting for case open, CPU voltage, and fan speed.

BIOS

1. 2M bit flash ROM, Award BIOS

733 is the processor. thats determining the speed of your system. compatible memory is SDRAM 256 mb, AGP video card geforce 1-4.

sana ok na sayo.

bakit di ka mag upgrade ng PC. marami namang mura dyan 16T ok na.

hi reason y it wouldn't start is because the 2 is not compatible, what u can do is get a Intel P4 not a celeronD check the socket size and make sure that it correspond with the board that u have. The board that u have uses a 478 socket size so u need to get a processor with the same socket size ok... that should do the trick