Question about Washing Machines

3 Answers

Bosch max wfl2000 washing machine

My bosch maxx wfl2000 doesn't complete cycle straight through? recently I have notice that my clothes where wet when cycle finished,however when i put the machine to just spin the job was completed.I also noticed that the active light flashing.About ten minutes into wash cycle machine stops and you have to press button again to get machine to restart.The fabric conditioner and main wash soap draw doesn't get used-soap tablets still there at end of wash.I've cleaned out soap drawer and used a washing machine cleaner but stiill the problem remains.

Posted by on

  • 3 more comments 
  • terry68 Nov 14, 2007

    I have a Kenmore Series 80 I think model starts with 110 and 22something after. Forgot offhand. Anyway, there is no leak whatsoever. The washer does what is suppose to. It spins when you start it and clothes are clean but when you retrieve them to place into dryer, they are soaking wet. What can this be? I was told to try spinning it and see but when i turn the knob to spin and pull out, it does not turn on? How can I try to spin again to see? Does this mean it is broken and in need of repairman even though there is no leak? Please advise. Thank You.

  • Mellyc Jan 05, 2008

    Just finished a 40 degree wash and the clothes have not been spun properly and now the machine will not spin at all. The same thing happened to my last Bosch machine which was less than 2 years old. My current machine is 13 months old, which is infuriating as it is just out of guarantee. What do I do next, as last time round it was the circuit board, and the symptoms today are exactly the same. I paid £380 for this one, what action can I take?

  • archimad Feb 11, 2008

    same problem here ... not completing the cyclus ...clothes wet ...

    by trying to put only the centrifuge on ... i here a tiny little blocked sound ...so centrifuge is not working ....

    probably could be a stuck filter .... try cleaning filter .......i'll try this later on myself

  • Anonymous Feb 18, 2008

    I have the same problem with my machine. At the end of the cycle the end light is flashing and Ithere is still fabric softern in the draw sometimes and I can see that the drum still has water in it and I have to run the spin over and over to get the clothes spun....... dont know what to do, please help

  • Anonymous Mar 29, 2014

    Any program the problem remains. the washing machine does not stop working.

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Just been through this with our Bosch Maxx, problem was the pump discharge pipe was blocked with soap deposits. I also removed the large black rubber pipe from the drum/pump and cleaned this out as well.
All working fine now.
SteveN

Posted on May 11, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 209 Answers

I am a recently retired appliance engineer of 20 years sounds like a faulty cold supply, or just no water getting to machine, if water supply ok check the water solenoid, check for open circuit just try that to start with, hope this helps if so rate me please

Posted on Sep 09, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Washing Mach... Master
  • 662 Answers

You should find the filter located behind a removable plastic panel at the bottom front of washer. Unscrew it anti clockwise to remove and clean it out.

Pl rate me 'very helpful' for the free help, thanks!

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bosch maxx Classic. 7 yo. Washing cycles are not finishing. Timer is showing 1 but does not turn off. Clothes are still quite wet. Have cleaned filter. Anything else I can do?


Looks like the solenoid that controls the drain motor is malfunctioning.
Whenever this happens, the water does not get drained fully and remains in the chamber thus keeping the clothes still wet.
Speak to your local service representative and get the part replaced.

Feb 22, 2015 | Bosch Washing Machines

1 Answer

How do I drain the pump on a bosch classic maxx model 18061 au


You will always have some water (up to a litre) left in the pump of any washing machine once the cycle has finished. On some of the Bosch models there is a short black hose next to the filter which will allow you to drain off this excess water in to a shallow baking tray before opening the filter. I there is no hose then usually you can drain straight into a shallow tray

Sep 20, 2014 | Washing Machines

1 Answer

Why is it that my washer is not completing the spin cycle,it is still very wet when it stop??


Hello there and welcome to fixya
The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these: Motor coupler
To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning:
If it's spinning when you lift the lid, the coupler is fine.
If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.
Spin cycle
If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.
Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.
Siphoning
If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.
Water-inlet valve
Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.


Sep 12, 2011 | GE Washing Machines

1 Answer

Hi, My Hoover 600MB top loading washing machine is approx 8 years old. Recently it has occassionally not fully spun out - clothes still wet at end of cycle. Now it also often doesn't agitate - just...


Have a look for coins etc stuck in the drain pump or the tub outlet hoses especially where they fit onto the tub. If a coin or other foreign material blocks the water flow when draining , these machines wont spin properly.

Jul 26, 2011 | Hoover Washing Machines

1 Answer

Bosch wfl2000 machine works on every cycle apart from spin, washes drains etc but wont spin. Cheched brushes and removed and had motor tested all ok, belt fine, any ideas- Controller!!


are you sure its heating the water as it will not complete the wash cycle if the heater has failed, hence not getting to the spin cycle. try testing heater or see if water is warm coming out or glass warms up

May 31, 2011 | Washing Machines

1 Answer

Clothes wet at program finish


The clothes are wet after spinning When the clothes are wet at the end of a cycle, check these:

Motor coupler
Spin cycle
Siphoning
Water-inlet valve
Motor coupler To test the motor coupler, re-start the washer in its spin cycle. Let the machine run for a minute, and then open the lid and notice whether the tub is spinning:

  • If it's spinning when you lift the lid, the coupler is fine.


  • If it isn't spinning--and your machine was produced by Whirlpool®--you may have a broken coupler. Many Whirlpool-made washers use a small, relatively inexpensive device called a motor coupling. This plastic-and-rubber component is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. When that happens, you need to replace it completely.


Spin cycle If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.

Alternatively, there could be clothes caught between the inner and outer tubs. Read the "It spins but won't pump" section of the "It won't drain" section. Also, there could be other things that cause friction on the drive train. Seek the assistance of a qualified appliance repair technician.

Siphoning If the water that pumps from the machine goes right back into the machine after the spin cycle, it may be because your washer is siphoning the water from a laundry tub with a slow drain, back into the washer. Try to improve the draining of the laundry tub. (Is there something stuck in the drain?) Also, be sure the drain hose doesn't reach more than about 4 inches into the laundry tub. If it does, cut off the excess.

Water-inlet valve Water-inlet valves eventually fail. One problem that may develop with a water-inlet valve is that it can no longer completely shut off when the electricity is turned off to it. Then, the valve may leak and drip water into the clothes tub--you may notice that your washer has water in it when you haven't used it for a few days. To fix this, replace the valve.

Apr 01, 2009 | Bosch Washing Machines

1 Answer

Bosch Axxis WFR 2460 Front Washer Drum/Cycles Not Working


hi sounds like the motor brushs are worn down,some bosch models you can change them without removing the motor ,but others its best to remove it,they just twist out,and to refit use a small blade flat blade screwdriver to tuck tab in,thanks

Aug 04, 2017 | Bosch Axxis+ WFR 2460 Front Load Washer

1 Answer

Bosch Nexxt 700 spin problems


yes it could be normal if the balance control senses that the load is uneven however the same problem could be caused by a blocked filter or blocked sump hose.

Dec 30, 2007 | Bosch Nexxt Premium WFMC6400UC Front Load...

1 Answer

Goes through washing cycle but doesn't dissolve the tablets or cleans the clothes.


Clean out your outlet filter; this is to be done regularly once a month, depending on your usage. Re your tablets not disolving, try using front loading washing powder. Also refer to your manual..........

Jun 10, 2007 | Bosch Classixx WFL 2066 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

2,153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...