Panasonic PT-47WX49 47" Rear Projection Television Logo

Related Topics:

Question about Panasonic PT-47WX49 47" Rear Projection Television

1 Answer

Panasonic PT-47WX42F does not come on

I have a panasonic PT-47WX42F television. went off and won't come back on . when power button is pushed, power led flashes 3 times. tv stays off. service manual or suggestion would be very helpful. My e-mail is [email protected]

Posted by Anonymous on

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 140 Answers

Manual on it's way...Good Luck

Posted on Sep 02, 2007

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

My tv won't turn on when the on button is pushed, but the power light blinks 5 times

5 times LED blinks in Panasonic PT-47WX42 shows problem with convergence out chips failure as this tv has two big black ICs STK392-110 as convergence output, replace them to fix tv problem.
0helpful
1answer

I have a panasonic 47wx42f. the power button blinks and no pic

how many times does it blink between pauses as it may be a error code
1helpful
1answer

Panasonic T.V. model number PT-47WX42F no picture or sound

R800 open on power board next to the relay.the resistor value is1.5 ohms 10 watt resistor.
2helpful
1answer

Panasonic PT-47WX42F outer most screen cracked

Look for a used Panasonic PT-47WX42F One in Local ads, Or place a wanted ad for your model. ~ Or if you want A new one, Get ahold of a TV Shop And OR Panasonic and be ready to spend lots of $$$$ ~ And yes there easy to replace!, Make sure you have a large clean area to work in, And a helper. Becarful and replace them back in as they came out! ( Top Bottom) they should be marked with a small tag or mark.... Geo*
1helpful
1answer

Panasonic PT-47WX42F does not come on light flashes 3 times HELP!

There is a service manual which should cover this model/chassis series:

Elektrotanya for electronics experts

(PDF format - free - no sign-up needed - 100% clean)

Page 11 ('auto diagnosis feature') shows a table of LED flashes and what each one means. I'd start by checking D-board (since that is power and deflection) and going from there.
0helpful
2answers

Panasonic 47wx42f projection

Joe,
It sounds like your may need to replaced your convergence ic's loc# ic7001 and ic7002 stk392-110. That should take care of your alignment problem.
4helpful
1answer

Panasonic Model No. PT-47WX42F

Replace the convergence amps. That unit takes two Sanyo STK392-110 and you could use 150's for greater reliability. Also replace one or more of the 1.2 ohm resistors in the yoke return circuit out front of the amps.
0helpful
1answer
0helpful
1answer

No voltage to convergence chips

There are usually 2 micro fuses that resemble 1/4 watt resisters around the power supply, and are usually all green,tan or yellow, and in most cases will have a + or - voltage marked right near these fuses 20 to 25 volts dc typical.
Not finding what you are looking for?

206 views

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5754 Answers

The Knight
The Knight

Level 3 Expert

76851 Answers

Jaime Hernandez

Level 3 Expert

2351 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...