Audio Players & Recorders Logo

Related Topics:

Question about Audio Players & Recorders

1 Answer

Satellite receiver not respond

I got a satellite receiver sonicview 4000 it has power on the receiver screen there aren't any channel number or clock time is just one digit I can turn on my receiver

Posted by rosalindarlm on

Ad

1 Answer

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,153 Answers

Search internet for JTagging sonicview receiver. You will need special equipment.

Posted on Sep 04, 2007

Ad

1 Related Answer

Anonymous

  • 520 Answers

SOURCE: satellite receiver

dont need factory to reflash.
turn of set at plug.press and hold backup on set(keep pressed)
turn on at plug.keep backup pressed for about 15 seconds.all lights on set will flash.if you have tv tuned to set screen will display updating system.dont turn off.when lights on set go off(about 10min later)set is reset(flashed)Press power on remote sky will restart like new.

Posted on Mar 10, 2008

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

9helpful
1answer

Locked up. buttons don't respond no sound. no change in screen. clock and station stuck.

hold your volume and mode button down for 3 or 4 seconds and release. This will reboot the radio.
1helpful
1answer

How to set the clock on vcr/dvd.

Make sure the antenna//cable TV connections are correct. Channels are set. If this unit is connected to a cable/satellite box, select the local PBS station on them to set the clock automatically.

There's an Auto Clock Setting. "This Unit can set the time and date automatically by reffering to a PBS station.". But I never had to do that, I just went to Setup and it already knew what the date and time was.

"Note: The clock may set itself automatically after you connect the antenna/cable signal and plug in the power cord. Only the analog PBS channel signal is effective for auto clock setting. The unit receives the clock data at 12:00 A.M./P.M. from the PBS channel when the power is off.

1 Press [SETUP] and use the up and down arrows to select "General Setting", then press OK.
"General Setting" menu will appear.

2. Use up and down arrows to select "Clock" then press OK.
"Clock" menu will appear.

3. Use up and down arrows to select "Auto Clock Setting", then press OK.

4. Use up and down arrows to select "Auto" then press OK.

5 Press SETUP to exit.

6. Press STANDBY-ON to turn off the unit.
This unit will search for the time only when the power is off. Leave it off for several minutes to give this unit time to set the clock.

If the unit chooses an incorrect PBS channel, set the PBS channel manually by following the steps below:

1. Select "Manual" at step 4, then press OK.
2. Use [the number buttons] or up and down arrows to enter your PBS channel number, then press OK.
3. Press SETUP and turn off the unit.

If this doesn't work, let me know and I'll type up the instructions for what to do if you need to actually set the clock manually.

Mathis...
0helpful
3answers

Satellite receiver not responding

reset the receiver again and try if its responding again
1helpful
1answer

FTA fix

try autorollbins
0helpful
1answer

SonicView 8000 HD FTA Satellite reveiver,,Info, Literature,Documents

User Manual:
http://sonicviewusa.com/downloads/manual/SVHD8000_Manual.pdf

Unfortunately, They do not even have a troubleshooting section it that User Manual, I don't know of a service manual, perhaps loading the factory firmware may clear up your issues.

SV-HD8000 Factory Firmware:
http://sonicviewusa.com/downloads/firmware/SVHD8000_Factory_20080108.zip

If that doesn't help, try contacting SonicView Directly at:
[email protected]
or
1-760-884-3171 (Mon-Fri 9AM - 5PM) Not toll-free
0helpful
1answer

I can't turn on my satellite receiver, it has power on the receiver screen is not a channel number or clock time just one digit

Is this a Pansat receiver? If so or not then you will have to find out about Jtagging your receiver. Maybe because bad script or just cloning you have to jtagg first then rescript.
1helpful
3answers

Satellite receiver

dont need factory to reflash.
turn of set at plug.press and hold backup on set(keep pressed)
turn on at plug.keep backup pressed for about 15 seconds.all lights on set will flash.if you have tv tuned to set screen will display updating system.dont turn off.when lights on set go off(about 10min later)set is reset(flashed)Press power on remote sky will restart like new.
0helpful
2answers

Satellite receiver not responding

was you satellite tampered with? If so then it could be an eeprom jam!
Not finding what you are looking for?

380 views

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts

Ekse

Level 3 Expert

13435 Answers

The Knight
The Knight

Level 3 Expert

76843 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...