Ps2 and watching movies

Turn your television and Apex DT250 receiver on.

Push the "Menu" button on the Apex DT250 remote control.

Press the remote's "Up" and "Down" buttons to scroll through the menu options. Stop when "Parental Controls" is highlighted. Press the "Right" button to select this option.

Enter your four-digit password. If you have not set your password, use the default code of "0000."

Use the "Up" and "Down" arrows to change or set the parental control movie ratings. You can select from "None," "G," "PG," "PG-13," "R," "NC-17" and "X." Once your setting is highlighted, press the "Right" button to go to the next screen.

Use the "Up" and "Down" arrows to change or set the parental control TV ratings. You can select from "None," "TV-Y," "TV-Y7," "TV-G," "TV-PG," "TV-14" and "TV-MA." Once your desired setting is highlighted, press the "OK" button to save your settings. Once the settings are saved, you will be taken back to the main menu. Press the "Exit" key to exit the main menu.

just slide the dvd in like a regular PS2 game and then let it play! if its a PG 13 - R movie then you have to put parental code in but dont worry, if you dont have a parental code then just type in (example) 1111 as the parental code

I can help you unlock your Mitsubishi HDTV V-Chip.

Please follow these steps to bypass the vchip or reset the V Chip password.

I hope that helps.
_______________________________________________
Reset Mitsubishi HDTV VChip Password
Bypass Mitsubishi HDTV Front Panel Lock

the password is the arrows you have to do forwrd,backward,forward,backward but use the doubke arrow keys. this should work i found the soloution the manual

this should solve your problem

http://forums.afterdawn.com/thread_view.cfm/203902

You can take your time putting in the code. I mistakenly had the impression
you had to time it just right. But no.

Just close the tray with no disc inside, it will say NO DISC.

On the remote, press MENU, the "non-applicable" slash circle graphic comes
up.

Then press 1, (same slash circle), then press 9, and the menu pops up.

My menu says:

Region : 1
Password : ____
Level : 8. Adult

By default, the region number is highlighted. This is where I got confused. I
pressed the control pad on the remote left and right and up and down and
nothing changed the number.

The only way to change the number is to press ENTER on the remote and it
then cycles through all the numbers available. I was never given a chance to
punch in a number, I tried it and it didn't work.

While I was here, I also set my password code and looked through the choices
for LEVEL. I think it is a system to limit the type of movie that could be
played, for instance, if the DVD player was for a child's room, you could limit
the level to G, PG, or PG-13 and it wouldn't play movies rated worse than
that. good luck
please mark the post with a fixya!

This is the only way to turn "off" parental control lock on the custom setup screen.

1) turn off ps2 with no dvd in drive.
2) turn on ps2 and insert dvd in drive.
3) when it asks about parental password, choose 'yes'.
4) when prompted for password, press 'select'.
5) the prompt will change and say 'delete password'. enter '7444'.
6) enter a new password (0000 works).
7) registration complete, dvd will start playing.
8) once the movie starts, press 'select'.
9) click the 'stop' icon.
10) click the 'stop' icon again (the icon must be gray even when you have it highlighted).
11) navigate to 'custom setup' ('select', setup icon, custom setup icon)
12) move to parental control option, press right directional button, enter password (0000).
13) move down to 'level'.
14) move up to desired level (off is at the top).
15) click 'x'.
16) go back to 'select' menu options, and press 'play'.
17) while movie is playing, eject disk and remove dvd.
18) turn ps2 off using switch on the back, keep off for five seconds.
19) turn on ps2, put dvd back in.
20) happy dance. ;)

When there is a parental code, you have to ring up your tv service provider for the code.

Hey Aurora, After you put your password in, go back and change the password using blanks spaces. Then it should reset to 'parental control off'. Let me know if this works. Some Sanyo models are different to reset.

This is from the soundstorm website: If your DVD player shows a "Parental Code" on the screen. Here is the factory default code. It is 3308. Once you have this code, you can go into the settings and change the level to whichever level you like. Here is a break down of the levels: Level 1 = G Rated Level 3 = PG Rated Level 4 = PG 13 Rated Level 6 = PG-R Rated Level 7 = NC-17 Level 8 = Adult Level 0 = No Parental