Got error of "PC cannot send datga to printer. Please check power

Check the network connection and or the USB cable. Go to Sharp web site and download the latest drivers for your machine and computer. they (drivers) are normally free.

http://siica.sharpusa.com/product-downloads

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Slow transfer of information to the printer can be a couple of things.
1) The document is massive. If you are sending a picture then check the size of the image file, same for normal files. More than 1Mb is going to take a long time unless you have a very powerful printer.
2) The Driver is not able to translate the file into a format the printer can accept. Try updating the driver.
3) The connection to the printer is sketchy. If the cable connecting the PC to the Printer is damaged some information will be getting lost as it is trying to send. Try replacing the cable.

49.XXXXX ERROR To continue turn off
then on
A critical firmware error has occurred.

Generally this fault occurs when a corrupt file is in the print queue
to clear fault follow these steps precisley
1. disconnect the net cable / usb cable or any other data cable that the machine is connected to
2. cycle the power with no data connections.
3. your machine should now come to ready.
4. take a copy from the platen glass ( straight forward photocopy)
if this prints out then the fault is down to corrupt data.
if at this point the error 49.xx.xx is still present then order a new formatter.
5. before reconnecting the networks -make sure ALL PRINT QUEUEs are cleared before connection otherwise you'll be back at square one
( print queues are on the computers sending print jobs)
before printing your documents its wise to send a test page through to make sure the printer is still able to understand print commands.
hope this helps...if you still need assistance please call Belmonte office equipment on 01614805556

Power the printer OFF and ON. Send the same file to the printer, if file has not been released from the print queue then delete all pending print jobs out of print queue.

Disconnect all data cables and power the printer OFF and ON. If the printer returns to READY, Reconnect the data cable and try printing again. If you are getting a paper jam error, please take not the error code and locate the jam. For further assistance, please contact Lexmark Technical Support.

try to download manual from the following site
http://support-au.canon.com.au/contents/AU/EN/0300299101.html

If above link does not work , clickon the below link to proceed....

http://www.canon.com.au/en-au/For-You/Printers/PIXMA-InkJet-Printers/MX340

If you like solution, please rate & vote...

Thanks
San

This is usually caused by data within the print job. Microsoft Office sends paper size and job data with each job. Clear all print jobs in the computer sending the job.(Start/Printers/double click the canon printer and delete all jobs in the print que. Clear the Canon by off/on. Open a program and print a standard letter size document to test. This can be corrected by going to the page/document setup choices under "File" or the Ball in MS Office. Usually this is set to A4 or Bypass by mistake within the application.
Thanks

You should try a copy to see if it prints OK, when the scanner goes out you sometimes get a black page and your fax machine knows it looks like way too much data.

: do u check with IP address?
Junoon007: The IP address of the machine where the data is saved and the name of the box are indicated in the body of the e-mail message

Junoon007: increase the machine's memory or change the scan settings
Junoon007: delete unnecessary documents from the hard disk, and then try sending again
Junoon007: type in the file name correctly
Junoon007: check that the box has not been deleted
Junoon007: a maximum of 100 documents can be saved in a single box.delete unnecessary documents from the box, and then try sending again
Junoon007: r u there sir?
Junoon007: check with above suggestions

check your rribbon.
also cjeck your head.
try to tast page from printer properties.
also try to print from dos .
check your printer datga cable.change it